aqueous slurry

a brief introduction of aqueous slurry pushing process for pigments

水性颜料浆直接转相技术简介

study on film formation and thermal stability of pp/ cmc aqueous slurry for rotational moulding

旋转成型PP／CMC体系的热失重行为和成膜行为研究

preparation of octenyl succinic anhydride ( osa) modified starches from raw material potato starch and acid hydrolyzed potato starch in aqueous slurry system were first studied.

本课题以马铃薯淀粉和酸水解马铃薯淀粉为原料，对辛烯基琥珀酸淀粉酯的湿法制备工艺进行了研究。

reaction of wheat starch with propylene oxide in aqueous slurry for producing hydroxypropyl wheat starch was investigated.

以小麦淀粉为原料，选用湿法工艺制备小麦羟丙基淀粉。

in this range, the aqueous slurry can not be well dispersed in the organic phase and the glass powder has the tendency of aggregation to form solid beads.

这是由于在该范围内，水性浆料在油相中不能很好的分散，包覆粉体有聚集形成实心颗粒的趋势。

stability of the pva aqueous slurry for the rotational moulding of polypropylene

聚丙烯旋转成型用聚乙烯醇浆液料稳定性的研究

The open cell alumina foam ceramics were prepared by impregnating sponge with aqueous ceramic slurry.

采用有机泡沫前驱体浸渍工艺制备氧化铝泡沫陶瓷.

the investigation of the drying behavior of the aqueous slurry of powdered polypropylene ( pp) using sodium carboxymethylcellulose ( cmc) as a suspension stabilizer during heating process in rotational moulding was carried out.

研究了以粉状聚丙烯（PP）为原料、以羧甲基纤维素（CMC）为稳定剂的旋转成型用水性浆液料的干燥行为。

investigation of the drying behavior of the aqueous slurry of powdered pp for the rotational moulding

酚醛树脂磨具成型料松散性研究聚丙烯旋转成型浆液料的干燥行为

study on sticking and drying process of aqueous slurry of powder pp for rotational moulding

聚丙烯旋转成型浆液料粘结和干燥工艺研究

Preparation of Si_3N_4/ B_4C aqueous slurry with high suspended solid

高固含量Si3N4/B4C水基悬浮体的制备

Dodecenly succinic anhydride ( DDSA) waxy corn starches with paste top viscosity and degree of substitution ( DS) were prepared by the base catalyzed reaction with starch granular in aqueous slurry.

在碱性条件下，蜡质玉米淀粉与十二烯基琥珀酸酐（DDSA）反应可制得较高黏度、适宜取代度（DS）的酯化淀粉。

an aqueous slurry was developed as a sort of raw materials in rotational moulding for the preparation of short glass fiber reinforced polypropylene composites.

改进了以浆液料作为旋转成型的物料，用于制备短玻璃纤维增强聚丙烯复合材料的新工艺。

preparation of si_3n_4/ b_4c aqueous slurry with high suspended solid and low viscosity is an essential step for forming si_3n_4/ b_4c green body by gel casting. however si_3n_4 and b_4c powders are very difficult to be dispersed. dispersion of aqueous suspension of fine particles

高固相、低粘度Si3N4/B4C水基悬浮体的制备是实现陶瓷材料凝胶注模成型工艺的关键和前提。微细颗粒水基悬浮体分散的研究

film formation of pp/ cmc aqueous slurry for rotational molding was investigated.

研究了旋转成型浆液用料聚丙烯（PP）／羧甲基纤维素（CMC）体系的热失重行为和成膜行为。

stability of cmc aqueous slurry for the rotational moulding of short gf/ pp composites

旋转成型用短GF/PP复合材料的CMC浆液稳定性的研究

in alkaline condition, reactions between starch and acetic anhydride may produce acetate ester starch in aqueous slurry systems.

原玉米淀粉于水相体系碱性条件下与醋酸酐作用生产醋酸酯淀粉。

the production of starch sodium dodenenyl succinic anhydride in aqueous slurry systems

水相体系十二烯基琥珀酸淀粉钠的制备研究

The technique of centrifugal casting was used. Study on Freeze-Casting of Aqueous Silicon Carbide/ Carbon Black Slurry

采用离心浇注法成型。水基碳化硅/炭黑料浆冷冻浇注成型工艺研究