crankshaft

Using Pressure-Controllable Feeder to Eliminate Shrinkage Defect of Ductile Iron Crankshaft

采用可控压力冒口消除球铁曲轴缩松缺陷

Optimization Design of Crankshaft Balancer of Piston Compressor Based on Pro/ Engineer

基于Pro/Engineer的活塞式压缩机曲轴平衡块优化设计

The irrational distribution of crankshaft counterbalance weight causes greater vibration.

曲轴平衡块质量分布不合理,会引起发动机振动大.

As the crankshaft rotates, the crankpin swings in a circle around the shaft.

随着曲轴的转动, 曲柄销绕主轴作圆周摆动.

A Tentative Study of Manufacturing ADI 480 Diesel Engine Crankshaft

奥贝球铁480柴油机曲轴的初步研究

The method of crankshaft vibration damper property and reliability experiments are discussed.

就曲轴扭振减振器的性能和疲劳试验的测试方法作相关探讨.

Only turn the engine on the crankshaft and never on the camshaft as the timing chain can jump over.

只能在曲轴上（不得在凸轮轴上）转动发动机，否则正时链条可能会跳起来。

The stiffness of crankshaft is measured and its characteristics are analyzed.

同时测量分析了不同角度上的曲轴刚度大小及其分布规律.

The camshaft rotates in phase with the crankshaft, but at half its speed.

凸轮轴和曲轴协调旋转, 但速度仅是曲轴的一半.

Remove vibration damper bolt and washer from end of crankshaft.

从曲轴端拆下减震器螺栓和垫圈.

An inward stroke , especially a piston stroke moving away from the crankshaft.

蒸汽机或其他发动机的活塞离开曲轴运动时的冲程.

Insert Timing Case Cover Alignment and Seal Installation Tool 6139 in crankshaft opening in the cover.

在曲轴盖的开口处,插入正时箱盖定位和轴封安装工具6139.

The engine had a broken crankshaft.

发动机的曲轴断了。

The crankshaft makes three rotations for each rotation of the rotor.

转子每转一周,曲轴转3周.

When the gears are engaged, the crankshaft keeps the car moving.

而曲轴,在齿轮箱挂挡时, 又使汽车持续运动.

In the engine, oil is supplied to crankshaft and camshaft journals rotating in their supporting bearings.

在发动机里, 机油被供应到旋转在其支承轴内的曲轴和凸轮轴轴颈上.

The motion of the rotor can be balanced completely with rotating counterweights attached to the crankshaft.

使用连接在曲轴上的转动平衡块,转子的运动就能完全平衡.

The diesel crankshaft cleaning equipment is designed based on the hydrodynamic calculation and experimental data.

通过大量的流体力学计算和实验参数来设计柴油机曲轴清洗设备。

Collection and Analysis of Fatigue Test Information of Engine Crankshaft and Its Applications

发动机曲轴疲劳试验信息的采集分析及应用

The timing is controlled by the camshaft which is synchronized to the crankshaft by a chain or belt.

凸轮轴通过皮带链接与机轴保持同步，准确控制了可燃气体的进出时间。

Overhead cam shaft Programming of Inner-milling of Crankshaft Drive Spindle with Parameters R

上凸轮轴上部凸轮轴基于R参数的曲轴主轴颈内铣加工循环编程

Pry the crankshaft forward , position the dial indicator to zero.

向前撬曲轴, 定位针盘指示表到0.

I steam operating company, Moldova accessories, rod, crankshaft, gears, ball, forging tools.

我公司主要经营汽 、 摩配件 、 连杆 、 曲轴 、 齿轮 、 球头 、 工具等锻件.

The crank is an offset section of the crankshaft.

曲柄是曲轴的偏置部分.

Remove and discard the front crankshaft oil seal.

拆下并抛弃曲轴前油封.

At present the crankshaft torsional damper for internal combustion engine is the combination of torsional damper and pulley.

目前应用的内燃机曲轴扭振减振器大多数是减振器和曲轴V带轮二合为一的产品。

The methodology to increase system robustness through Design for Six Sigma ( DFSS) is presented and demonstrated through the extension of the case study of crankshaft journal lobing design robustness improvements.

以六西格玛设计（DFSS）来提高系统稳健性的方法，也将通过对曲轴轴径凸角的稳健设计改进的案例研究来进行介绍与论证。

Install new front crankshaft oil seal.

安装新的前曲轴油封.

Research on a crankshaft rolling and aligning system based on artifical neural networks

基于人工神经网络的曲轴滚压校直系统研究

Development and Application of ADI Crankshaft for Turbocharged Diesel Engine

增压柴油机等温淬火球铁曲轴的开发与应用