fault-tolerant

In the fourth chapter the more details of realizing the fault tolerant flow control is discussed, and and the CRR is settled by the conclusion of FDD and the real-time function calculation which achieve the goal of the system control rule on-line reconstruction.

第四章进一步探讨了主动容错在流程控制中的实现问题，即根据故障诊断的结果，实时计算故障函数，在线修改系统的控制律的方法来实现容错控制律重构。

Fault-Tolerant Control Based on Characteristic Extract and Its Application

基于特征提取的容错控制及其应用

Multiple models nonlinear active predictive fault-tolerant control based on LS-SVM

基于LS-SVM的多模型非线性主动预测容错控制

The characteristics of the multi agent system are distributed and collateral and strong fault tolerant ability.

多智能体系统具有在空间上是分布式的、并行的,且系统的容错能力较强等特点.

The dual-modular redundancy with comparison ( DMRC ) structure is a kind of widely used low-cost fault-tolerant structures.

双模 比较冗余结构是一种广泛应用的低成本 容错 结构.

A Fault-Tolerant Control Method for Basis Weight Control of Papermaking Process

造纸过程定量环节容错控制方法研究

An Intelligent Fault-Tolerant Flight Control Computer System Based on Serial Bus

一种基于串行总线的智能容错飞控计算机系统

Fault-tolerant Controller Design for Linear Continuous Control Systems with a Small Time-delay

具有小滞后的连续控制系统的容错控制器设计

Through the analysis the fault-tolerant computer system has a very high reliability.

通过分析可以发现该容错计算机系统具有很高的可用性。

With the detailed introduction of fault-tolerant technique, a typical fault-tolerant technique scheme was proposed.

在详尽介绍 容错 技术的基础上, 设计了一种现代航天器飞行控制系统三余度容错技术方案.

Fault tolerant ability is an important aspect for overall evaluation of distributed system ( DS ) .

容错性是全面评价 分布系统 的重要方面.

Nonlinear Analysis and Fuzzy Fault-tolerant Control of Complex Ecological System

复杂生态系统的非线性分析与模糊容错控制

Most of functions need software to achieve, including on board data handling, telemetry, telecommand, attitude control, power control, orbit, communication, etc. The thesis introduces the main function and fault-tolerant design of the software.

卫星的星务管理、遥测、遥控、姿态控制、电源管理、通信控制、轨道控制等都需要通过计算机软件完成，介绍了这些软件的主要功能和容错设计。

In addition, an untied kalman filter fault-tolerant structure has also been completed basing on hardware redundancy.

除此之外,还在硬件冗余的基础上, 设计了联合卡尔曼滤波器 容错 结构.

Most telecommunications systems use pessimistic message logging approach as basic software fault tolerant means.

交换系统一般采用悲观的消息日志法作为软件容错的基本方法.

Redundancy indicates that the system is fault-tolerant to a certain degree.

冗余是指系统有一定的 容错 能力.

Study on Fault-Tolerant Based on Modular Method in the Development of Test and Control System Software

基于模块化的容错技术在测控系统软件开发中的应用研究

An algorithm of fault-tolerant control with state feedback control system

状态反馈控制系统的容错控制策略

This paper proposes a self-routing fault-tolerant switching network for ATM switching systems.

本文提出了一种自寻径、容错的ATM交换结构.

Study on Fault-Tolerant Control of Three Phase AC Variable Frequency Drive System

三相交流变频驱动系统的容错控制研究

Tolerant control strategies are established based on different fault types so that vehicles can furthest keep running capacity.

将各故障分为不同等级，提出相应的容错控制方法，使车辆在发生故障时能最大限度地保持继续行驶的能力。

Fault self-diagnosis capability is the key element in the redundant fault-tolerant control.

冗余 容错 控制的关键在于故障的诊断.

System Structure and Fault-Tolerant Mechanism Based on Web Database

基于Web的数据库体系结构与容错机制

The fault-tolerant processing technology is more perfect, more human.

通过比对容错处理技术处理的前后，该容错处理技术效果明显，更符合人性化要求。

Finally, highly discussed the website in the overhead construction to expand accommodates, fault-tolerant .

最后, 在架构的高度讨论了网站扩容, 容错 等问题.

Fault tolerant technology for dynamic systems includes fault detection, fault isolation ( FDI ), and system reconfiguration.

所讨论的动态系统的容错技术包括故障检测 、 故障定位和系统重构技术.

This shows that the crossed cube is a network with better fault tolerant properties.

研究结果表明,交叉立方体是可重构性和容错性皆佳的网络.

By using redundancy computing and dynamic transference method, the fault tolerant become more easily and reliably.

采取冗余计算和动态迁移策略使得对等式计算模式中的容错性实现更容易、可靠.

Results from computer simulation show that the precision of the fault-tolerant control approach is satisfactory.

仿真结果表明,该控制器及 容错 控制策略都能达到很好的控制精度.

The need of simultaneous stabilization or pole-assignment is due to de-signing fault-tolerant control systems.

同时稳定或极点配置是出于设计容错控制系统之所需.