feed rate

The variations of feed conversion rate and daily body weight gain were extremely consistent.

各组饲料转化率的高低与日增重的变化完全一致.

The process variables were screw profile, feed rate, and screw speed.

本研究之加工变数为:螺丝元件组合, 进料速率及螺轴转速.

In fact, it is almost always less than the feed rate.

实际运动速度通常小于编程进给速度.

The hardware and software structure of a CNC system for high feed rate punching ma-chine is introduced.

介绍了一种冲床高速送料数控系统的硬件和软件结构。

Based on the designed thin film evaporator, the influence of the rotor speed, feed rate and liquid inlet temperature on evaporation length and film heat transfer coefficient was primarily discussed using the software CFX 4.4 with water as feed liquid.

针对自行设计的薄膜蒸发器，以水为物料，采用大型CFD软件CFX4.4，初步探讨了刮板转速、进料量、进料温度等参量对薄膜蒸发器蒸发段长度和加热段膜内传热系数的影响。

Using AC motor speed control system directly and cutting feed rate to achieve high quality cut.

采用AC马达调速系统直接控制切割进刀及速度,以达到高品质之切条.

The influence of depth of grinding, feed rate and circular linear speed of the grinding wheel on the grinding forces with respect to the maximum chip thickness of a single active diamond was analyzed.

从单颗金刚石最大切削厚度的角度，分析了磨削深度、进给速度和砂轮线速度对磨削力的影响。

Cutting forces increase with feed rate in both MQL and dry cutting.

干切削与微量润滑时，切削力均随进给量增加而上升。

This paper reports that of 24 head of Red deer, 15 head died during the experiment with carbamide feed, The death rate was 61.7%.

本文介绍了我地区某鹿场饲喂添加尿素饲料试验的24只马鹿中，突然死亡15只，死亡率达61.7%。

Effects of feed rate, feed fraction, reflux ratio and feed position on reaction distillation were investigated.

考察了进料流率, 进料组成, 回流比,进料位置对反应精馏的影响.

A new system of rapid roll carriage infeed and return, together with automatic selection of pressure and feed rate, has improved the already impressive floor-to-floor times achieved.

快速辊子进给和返回系统和自动压力、进给速率调节器提高了工作效率。

High feed rate full-automatic CNC punching machine

高速全自动数控冲床研制

Effect of Cutting Speed and Feed Rate on UVC Hard Cutting

切削速度与进给量对UVC硬态切削加工的影响

High feed rate CNC system for punching machine

冲床高速送料数控系统的研制

Please slow down wire feed rate.

请放慢送丝速度.

A more prudent its size, the greater the feed rate, a stronger ability to eat thick, more continuity sewing speed.

其具有更稳重的体积、更大的送料幅度、更强劲的吃厚能力、更加连续性的缝纫速度。

The influences of grinding depth, feed rate and circular linear speed of the grinding wheel on the grinding forces and the forces on each diamond grit were obtained.

对不同粒度条件下磨削深度、进给速度和砂轮线速度对磨削力的影响进行了分析。

The emulsifier content and feed rate affect latex swelling and shell polymerization by the making a change of latex number and total reaction rate coefficient respectively.

乳化剂量和加料速率分别通过影响胶粒数和总体反应速率系数而对胶粒溶胀和壳层聚合反应产生影响。

Meanwhile the lim it of feed rate is calculated both analytically and geometrically.

同时结合几何方法分析并计算了进给速度的变化范围.

Based on the results, the process calculation of thin film evaporator was realized by synthetically considering the optimum feed rate derived from CFD simulation.

以此为基础，综合考虑CFD数值模拟得出的最佳进料量要求，实现薄膜蒸发器的工艺计算。

Inverse time feed rate code

反比时间进给率代码

When velocity ( feed rate ) is not constant, several problems can result.

当 进给速度 不恒定时, 会造成许多问题.

Besides, the product purity also can be raised through controlling the feed rate of the light-off tower, or adding nitrogen in the top of light-off tower.

此外，控制脱轻塔的进料量和在脱轻塔顶加入氮气进行吹扫也能解决产品质量不达标的问题。

High-speed, high feed rate.

高速度 、 高进刀量钻孔.

If we controlled the rotational speed and feed rate well of the homemade tubular reactor, product discharge was in good condition, and the yield was78%.

自制管式反应器控制转速和加料速度，产品出料情况良好，且收率达到74.5%。

The growth rate, feed conversion ratio and the carcases quality of swine are not only the major economic criteria of swine production but the important traits for the swine improvement.

猪的生长速度、饲料转化率和胴体质量是主要生产经济指标，也是重要的育种改良性状。

This paper analyzes the phenomenon of that the cylinder oil for the main engine is not used properly in some ship companies, points out the allowable range of cylinder oil feed rate and discusses about how to confirm the correct feed rate in different ship types.

就国内船公司普遍存在的主机汽缸油不能正确使用的现象进行了较全面的分析，指出汽缸油允许使用的注油率范围，并对不同的船舶类型应该怎样确定合理的汽缸油注油率进行探讨。

Research on Steady Feed Rate of SSV

逐点比较法进给速度的稳恒研究

Computer Aided Selection of Sawmill Feed Rate

锯机进给速度的计算机辅助选择

The interpolation precision of pulse multiplier-based fine interpolator is related with the max feed rate, pulse equivalent of CNC, interpolation cycle, and output pulse frequency of pulse generator and the main reason of its error production comes from the rounding processing of crossover frequency number.

基于脉冲乘法器原理的精插补器的插补精度与最大进给速度、机床系统的脉冲当量、插补周期以及脉冲发生器的输出脉冲频率有关，其误差产生的主要原因是由分频数圆整造成的。