The field emission current density distribution over the tip surface was established using Fowler-Nordheim function, and the emission current over the single tip established by integrating the current density all over the single tip surface was 7 μ A.

The effect of TiC coating in electrode tip surface on spheriform electrode degradation during resistance spot welding zinc coated steel was investigated by SEM, EDX and XRD.

利用SEM、EDX和XRD等方法分析了在点焊镀锌钢板时球形电极表面熔敷TiC涂层对电极失效的影响。

When the tip surface energy was kept unchanged, the minute change in the surface energy of the GeSb_2Te_4 film would cause a significant change in the adhesive force.

当针尖表面能一定时，粘附力的微小变化可以导致GeSb2Te4薄膜的表面能产生较明显变化；

In the present paper, by using silicon rubber made in China, the successful measurement results of displacement fields in crack tip surface are concisely introduced.

本文简要介绍作者们利用国产硅橡胶材料测定裂纹尖端表面位移场的研究成果。

The Study of Deposition of TiC on the Electrode Tip Surface of Resistance Spot Welding by Vibrating Electric Sparking

点焊电极表面振动电火花熔敷TiC的研究

The remained contact area in the center of the tip surface help to maintain satisfactory weld quality.

电极头中部残存接触区的存在有助于维持较好的焊接质量。

Temperature Distribution and Fin Efficiency at the Tip Surface and Lateral Surface of a Circular Shell Casing

薄壳圆套管端面和侧面的温度分布及肋效率

Research of defects detection on metal axis tip surface and dimension measurement system

轴尖表面缺陷检测及尺寸测量系统研究

The Euler/ Kirchhoff method is adopted to calculate the far field noise of UH-1H rotor, and the calculated results are compared with the measured data. The effect of rotor blade tip shape on high speed rotor noise is investigated.

采用CFD与计算声学相结合的Euler Kirchhoff方法对UH-1H直升机旋翼跨声速悬停流动的远场噪声进行定量计算，并将计算结果与实验值进行比较，验证了Euler Kirchhoff方法的正确性。

I will tell you that this symbol jumps from her pens tip with such speed that it is impossible to follow the method.

我会告诉你，这个符号从她的笔与这样的速度，这是不可能遵循的方法技巧跳跃。

The simulation results show that, the wind turbine operates with the best tip ratio speed under rated wind speed. The proposed control method has better control performance.

仿真结果表明，在额定风速以下风力机能够有效地保持最佳叶尖速比运行，所提出的分数阶PIλ控制方案具有更好的控制效果。

Therefore, the low tip tangential speed design of high bypass ratio is a trend.

因此低叶尖切线速度是将来大涵道比风扇的发展趋势。

Based on the model, the paper studies how to design wind turbine controller, enables the system operating in the vicinity of the maximum power point, when the wind speed below the rated wind speed. That is the tip speed ratio lies in the optimal value.

在建立的模型基础上，研究了当风速在额定风速以下时，如何设计控制器使得风力机运行在最大功率点附近，也就是说将叶尖速比控制在最佳值。

Combined with the simulation results and the vertical axis of the impeller tip speed ratio theory, that is required to improve the transmission speed increasing ratio, in order to meet the project of Hydropower for water flow energy with low water speed.

结合仿真结果以及垂直轴叶轮叶尖速比的理论推导，表明需提高变速箱增速比，才能符合水流发电装置低水速运行的要求。

A conventional fixed pitch vertical axis turbine cannot usually start rotating on its own and only is able to work efficiently at very high tip speed ratios. As a result, a self-start motor will be required.

而传统的定桨距垂直轴水轮机构通常不能够独立的启动旋转且只能在非常高的速率下有效地工作，因此自启动马达是必需的。

Introduction is given to the state of compressure ratio, maximal wheel tip speed, and maximal exhaust temperature, as well as mix-flow trend of turbine and the reliability of radial turbocharger.

介绍了径流增压器压气机压比、最高轮周速度、涡轮混流化、最高废气温度和可靠性等方面的发展现状。

Variable pitch vertical axis turbines have been proposed, which can markedly increase the power extraction efficiency at low tip speed through controlling the rotor blades pitch at all points of their rotation cycle.

目前已经提出了一种变螺距垂直轴水轮机，它可以通过控制转子在一个旋转周期上所有点的叶片间距来显著提高能量的提取效率。

The reliability of blade is directly related to the safe operation of the entire system, the rotational speed and tip speed ratio is a directly affects the performance of the wind turbine.

叶片的可靠性直接关系到整个系统的安全运行，叶片的转速、尖速比等直接影响风力发电机的性能。

Simulation results show that the fuzzy Control System had tracked of the best tip speed ratio when the wind speed is low, and get a stable output power when the wind speed is high.

仿真结果证明，模糊控制系统在低风速时很好的跟踪了最佳叶尖速比，在高风速时得到了稳定的输出功率。

The influence of solidity and aspect ratio on power coefficient of H-type vertical axis wind turbine, and the change of attack angle with tip speed ratio were analyzed.

采用多流管模型分析了H型垂直风力机展弦比和实度对其功率系数的影响，并对叶片旋转过程中攻角随尖速比的变化进行了分析。

And this paper analysis and research the whole system and establish mathematical model, result in which the changing power-load adjusting is the control way of the best Tip Speed Ratio.

本文分析研究并建立系统数学模型，根据系统模型确定最佳叶尖速比的控制采用可变功率负载调节方法。