Study on plasma chemical reaction of water interface corona discharge desulfurization and denitrogenation

The reaction of the interface layer did not significantly reduce further corrosion.

反应生成的界面层并不能明显降低腐蚀进一步发生的速率。

The microstructure and the reaction of the interface are analyzed.

初步探索了在本文工艺条件下，碳化硼与铝的微观界面结构和界面反应。

The high tensile stress parallel to the interface exists at the whisker/ reaction layer interface and in TiC near the interface, at which failure occurs easily when shear force is applied.

SiC晶须/反应层界面及其附近的反应产物TiC内具有较高的平行于界面的拉应力，当连接界面承受剪力作用时，SiC晶须/反应层界面和TiC处极易破坏。

The results show that the chemical damage includes interface reaction and interface diffuse, in which the active groups of PCS hardly react with carbon fibers.

研究结果表明，PIP工艺中碳纤维的化学损伤包括界面反应和基体向碳纤维内部的扩散反应。

Effect of interface reaction and interface tension on wettability of Sn-Zn-Bi solders;

试验结果表明，该泡沫溶液的表面张力和界面张力很低。

The diffusion of WO_3 is the restrictive step of reduction process of WO_3. Improving fluidity of slag and enlarging areas of reaction interface can accelerate reduction process of WO_3. The use of damping preparation can restrain volatilization of molybdenum oxide effectively.

还原WO3的限制性环节是WO3在熔渣中的扩散，改善渣的流动性，扩大反应界面能加快WO3的还原；使用阻尼剂能有效抑制钼的挥发。

The SEM morphological observation shows that the dissolution of arsenopyrite starts from the edges of the cube and the weak areas such as fractures. Then, the reaction interface gradually migrates into the inner part of the mineral cube.

对反应产物的扫描电子显微镜（SEM）形貌观察显示，毒砂的氧化溶解反应从立方体样品颗粒的裂隙等薄弱部位和颗粒边缘开始进行，反应界面逐步向立方体内部迁移。

Microbial oxidation of pyrite is one of the most common microbial metabolisms existing in the nature. A series of biogeochemical process from the formation to oxidation of pyrite reflects the fluctuation of the REDOX reaction interface.

微生物氧化黄铁矿作用是自然界中存在的一种极为普遍的微生物新陈代谢作用方式，黄铁矿自形成到被氧化的一系列生物地球化学过程可以有效反映沉积环境中氧化还原反应界面的波动。

Meanwhile, the rare earth elements can eliminate the oxide film on the reaction interface between graphite and molten aluminum, and improve the wettability between them, and promote the synthesis of TiC phase.

同时，稀土元素清除了石墨与铝熔体反应界面上的氧化膜，改善了铝熔体对石墨的润湿性，促进了TiC相的合成。

In all temperature ranges, concentration of vapor at reaction interface went up, also did the thickness of product layer and densification with the increase of reduction degree. These caused the decreased reduction rate.

在整个温度范围内，随着还原率增加，反应界面周围H2O汽浓度逐渐提高，反应产物层厚度和致密度也逐渐增加，还原速率相减小。

The results of scanning electron microscope ( SEM) showed that there was a clear reaction interface in the Pb-Sb complex sulfide ores particle.

扫描电子显微镜（SEM）结果显示，铅锑复杂硫化矿颗粒存在着一个明显的反应界面。

The paper studies the elastic strength and softness of napkins by using reaction interface analysis, finding out optimal engineering conditions and improving napkin quality remarkably.

本文用反应表面分析，研究了卫生纸的弹性强度和柔合性，找到了最佳工程条件，显著提高了卫生纸的质量。

Development of Sb Microelectrode and In situ pH Measurement of Electroless Nickel Reaction Interface

锑微电极的制备及化学镀镍反应界面pH值的原位测量

Interface width and carbon concentration in reaction interface have been determined by electron energy loss scope.

用电子能量损失谱仪测量了反应界面内的C浓度变化，测出了界面层的宽度。

The V-type metering system which can infinitely adjust the ratio is developed based on the analysis and compari-sion of the various types of polyurethane metering systems and the performance characteristics of self-developed reaction injection molding machine.

在对各种类型的聚氨酯计量系统进行分析比较的基础上，结合自行研制的反应注射成型机的工作特性研制出可进行无级比例调节的楔形计量系统。

The content and technique trend of the computer simulation technology of the plastics processing and the computer simulation of three techniques of the injection molding, the gas assisted injection molding and the reaction injection molding are introduced.

介绍了塑料成型加工过程中计算机模拟技术的内涵和技术发展状况，阐述了塑料注射成型、气体辅助注射成型和反应注射成型等三种工艺的计算机模拟技术。

A brief introduction was made on a new reaction injection molding machine mixing system-batch rotary injection reaction injection molding ( RIRIM) machine mixing system studied and designed according to laminar shear mixing theory.

介绍了用层流剪切混合理论研究设计的新型反应注射成型机的混合系统&旋转注射反应注射成型机混合系统（间歇式）的混合原理和和特点。

The basic steps of the technology are: first manufacturing prototype using Stereo Lithography Apparatus, and then making mold using the prototype, and last molding product by reaction injection molding.

基本步骤为：首先使用立体光固化快速成型设备制造制品的原型，再以原型为基础模型快速制造模具，然后使用反应注射成型设备快速加工制品。

Molding method, process, equipment and mould design of reaction injection molding and reinforced reaction injection molding were discussed in this paper. MODIFICATION OF DICYCLOPENTADIENE FOR REACTION INJECTION MOLDING SYSTEM

论述了反应注射成型（RIM）与增强反应注射成型（RRIM）、注射成型的方法、工艺、设备和模具设计方面的问题

On the other hand, such study is also important from industrial perspective, and it can offer technological guidance to such industrial processes as reactive blending and reaction injection molding.

在另一方面，偶合化学反应的相分离的研究对于工业上的反应共混与化学反应注塑成型等过程也具有技术上的指导意义。