Matching and Calibration of the Key MAP for Diesel Engines with Electronic Control Unit Pump System

Through a summary and analysis for the key map and transportation design in Heng yang Caustic soda plant, Several methods and skill of combinating future items with currents items in this field are introduced.

根据衡阳烧碱厂总图运输设计的小结和分析，介绍工厂总图运输设计近远期结合的一些方法和技巧。

Prospect on technical transformation of key map transportaton in Angang

现代化安钢总图运输技术改造的展望

Making Zinc Powder from Zinc ingot with Reverberatory Furnance Process Study on Several Problem of Zinc Ingot Mold Production

锌锭反射炉法生产锌粉实践锌锭模制造问题探讨与研究

Macro-segregation of a steel ingot in a rectangular mold with a riser was simulated and the calculation result was compared with that of an experiment.

对带冒口铸钢锭的宏观偏析进行了数值模拟，并同实验结果进行了比较。

Research on transient stress fields in ingot and mold during solidification of ingot

钢锭与锭模在钢锭凝固过程中应力分析的研究

Thermal fatigue is the most common failure mode of mould, especially for large ingot mold. At present, failure hot work moulds because of thermal fatigue crack account of 70% in total failure molds in our country.

热疲劳是模具最常见的失效形式，对于大锭铸模尤其如此，目前我国热作模具因热疲劳裂纹而失效的占模具失效总数的70%左右。

This paper studies the influence of the change of flow direction of cooling water at the botton of ingot mold and the mold material on the crack and the inner surface roughness of the ingot mold.

对锌锭模制造经过多次的改进试验，主要改进了锌锭模下端面的冷却水流向和材质，研究其对锌锭模的断裂、内腔表面粗糙度的影响；

Based on the corresponding relationships simple method for analysis of ingot mold Life was proposed. In addition, the influence of ingot mold geometry on the ingot mold life was studied.

本文借助该关系提出了用温度场分析锭模寿命的简便方法，并据此分析了锭模结构对锭模寿命的影响。

As it was melting away I hurried off to finish welding a large ingot mold from heavy angle iron.

由于这是融化我跑去找完成沉重的角铁焊大型钢锭模。

Thermal stress measurement of 4.5t ingot mold of vermicular graphite cast iron in service

4.5t蠕墨铸铁钢锭模在使用过程中热应力的测定

The properties and service life analyses for middle and small-sized RE-Mg ductile iron ingot mold

中小型稀土镁球铁钢锭模的性能及使用寿命分析

Argon blowing through a metallic nozzle at the ingot mold bottom

金属喷头模底吹氩

The Effect of Boron Surface Alloying on the Service Life of Grey Cast Iron Ingot Mold

铸渗硼对灰铸铁钢锭模寿命的影响

Corresponding relationships between the temperature field and stress field in ingot mold was revealed by FEM analysis.

有限元分析结论表明锭模应力场与温度场存在明显的对应关系。

Using Numeral Simulation to Optimize Casting Method Design of a Heavy Vermicular Iron Steel Ingot Mold

用数值模拟优化大型蠕铁钢锭模工艺设计

The inverse problem method of heat conduction in the research for the thin walled ingot mold

钢锭模薄壁化研究的导热反问题方法

The Research on the Quality Improvement of the Medium Mn and Low Si Steel Ingot Mold

提高中锰低硅钢锭模质量研究

Casting Process Design and Production of Aluminum Ingot Mold Export to the United States

出口美国铝锭模的工艺设计及铸造生产钢锭模准备和脱锭跨

Investigation for the Main Factors Affecting Ingot Mold Life

影响锭模寿命结构因素的研究

Study of Improving 20 kg Al Ingot Mold of Casting Machine

20kg铝锭铸造机铸模改进方案探讨