plastic method的例句大全

According to the basic design theory, the bridge design method can be divided into: the elastic design method and the plastic method.

钢桥的设计方法按其设计理论大体可分为弹性设计方法和塑性设计方法。

This article introduces a method to determine the plastic membrane tensile modulus by using a normal mart electron tensile testing machine and computers.

文章介绍了一种利用普通的智能电子拉力试验机配以计算机来计算塑料薄膜拉伸弹性模量的方法。

An intelligent control method based on the production rules has been used in a plastic film thickness control system.

通过对聚炳烯塑料薄膜厚度测控系统的分析，建立了一套产生式规则系统，采用智能控制算法对薄膜横向公差进行控制。

Test method for interlaminar tensile strength of glass fiber reinforced plastic laminates

GB/T4944-1996玻璃纤维增强塑料层合板层间拉伸强度试验方法

Test method for tension& tension fatigue of fiber reinforced plastic laminates

GB/T16779-1997纤维增强塑料层合板拉-拉疲劳性能试验方法

Computational method on axial tension of secondary load RC members strengthened with carbon fiber reinforced plastic sheets

碳纤维布增强二次受力RC构件轴拉计算方法

The article has applied the weighted residual method and laplace changing to analyze the plastic dynamic response of a simple circular plate, the influence of elastic foundation on it and drives its residual deflection and the terminal time.

应用加权残值法和拉普拉斯变换，分析弹性基础上简支圆板的塑性动力响应问题，弹性基础对薄板塑性动力响应的影响，并且给出板的残余挠度和终止运动时间。

Thermal conductivity in a contact interface is an important parameter in engineering thermal design. Generally, it is tested with a steady-state method which however cannot test contact thermal conductivity under large plastic deformation.

接触界面热导是工程热设计中的一个重要参数，目前国内外普遍采用稳态法进行测量，但该法不能测试大塑性变形下的接触热导。

Research drainage by zipper type of plastic hidden pipes by using electric imitation method

电拟法研究拉链式塑料暗管田间排水

The plastic material processing routine is also the universal method to make the thermoplastic plate of low temperature of VC/ VAc copolymer that accords with medical requirement that its softening temperature is 55 ℃.

采用常规的塑料加工成型方法及设备制造出软化点为55℃的、符合医用要求的低温热塑性氯醋共聚树脂板材。

Test method for short-time hydraulic failure pressure of fiber-reinforced thermosetting plastic pipe

GB/T5351-1985纤维增强热固性塑料管短时水压失效压力试验方法

Test method for longitudinal compressive properties of fiber-reinforced thermosetting plastic pipe

GB/T5350-1985纤维增强热固性塑料管轴向压缩性能试验方法

Test method for external loading properties of fiber-reinforced thermosetting plastic pipe by parallel-plate loading

GB/T5352-1985纤维增强热固性塑料管平行板外载性能试验方法

An Elasto-Plastic Analysis of Thick Shell Structures by Semi-Analytical Finite Element Method

厚壳结构弹塑性分析的半解析有限元解

According to the residual strength of casings after tubercular corrosion, with elastic-plastic finite element method, the changes of collapse resistance, burst strength, and tensile resistance of casings are analyzed.

为此，文章建立CO2点蚀模型，以点蚀后套管的剩余强度为出发点，应用弹塑性有限元方法分析了点蚀套管的抗挤强度、抗内压强度、抗拉强度的变化。

And then, based on the subroutine developed above, this paper operates static elasto-plastic analysis on a three-dimensional frame structure and gets the target performance point of the structure by using the capacity spectrum method.

然后基于开发的材料子程序，对三维框架进行静力推覆分析，并运用能力谱法计算得到结构的目标性能点。

Element Free Galerkin Method for Elasto-Plastic Problems With Large Deformation Distortion

弹塑性大变形畸变问题的无网格分析

The curves of structural seismic total input energy, hysteretic dissipated energy and damping energy are obtained using time history analysis method to analyse elastic-plastic structural.

通过结构弹塑性地震反应分析的时程分析法，可以计算出结构地震总输入能及结构阻尼耗能和滞回耗能的时程曲线。

Regarding the facial soft tissue deformation problem in simulation of plastic surgery, this paper propose a simplified method of human facial modeling using geometric finite elements which is based on cylinder projection.

针对模拟整形手术中面部软组织变形问题，本文提出一种简化的基于柱面投影的几何有限元建模方法。

To collect the bone marrow aspiration specimens of non-malignant tumor patients, by the method of density gradient centrifugalization to obtain bone marrow stromal cells and culture them which adhere on the cultural bottles' plastic surface.

【方法】1.收集血液科非恶性肿瘤患者骨髓液标本，梯度密度离心后，通过贴壁法培养骨髓基质细胞。