roller diameter的例句大全

A Press Production Line of Fourdrinier 3600 and Large-Roller Diameter Multi-Cylinder.

一条3600多长网多缸大磙径压榨生产线.

in order to meet with production needs, designed core roller diameter option ruomuo fig.

为满足实际生产需要，设计了芯辊直径选择的诺谟图。

An improperly designed hot roller can cause fabric edge in excess of rolling pressure due to the increased roller diameter near the journal ends.

不适当的热轧辊设计会导致织物边缘过度轧压，这是因为热轧辊端部附近直径增大引起的。

the essential principle and the classified integration scheme of measuring roller diameter with ccd sensor are introduced in the paper, which can realize the on-line automatic measurement and classification of large numbers of rollers, and enhance the assembly precision of ball bearing.

介绍了CCD传感器测量滚针直径的基本原理，制定了分选整体方案，以实现滚针的自动、在线大批量测量和分选，提高滚动轴承的装配精度。

The paper describes roller mill about its structure and working principle, makes analysis and determination to optimization of such parameters as pull-in angle for material, diameter of cylinder, diameter of roller and average granularity for feeding.

阐述了辊筒磨的结构和工作原理，并对辊筒磨的物料拉入角、筒体直径、磨辊直径以及入料平均粒度等结构参数进行了优化分析和确定。

overall width of the assembled bearing; refers to the combination of sizes of the cone, outer diameter, cup, inner diameter, and roller.

整套轴承的总宽度；参考内外圈尺寸，外径，内径以及滚子。

the deep end-cavity roller reduces its maximum contact stress by 22.33 percent than the common column roller, and the depth of its deep end and the diameter of its notch are optimized to 4.4 mm and 5 mm respectively.

与普通圆柱滚子相比，凹端圆柱滚子最大接触应力降低22.33%，其优化结构参数为凹端深度4.4mm，凹口直径5mm。

Diameter of punched driving roller is large, suiting rewinding of large and small roll.

复卷驱动辊直径大, 适应大小卷径的复卷.

According to features of thick wire electrode ( diameter 1mm) ( aging bending deformation, loss lengthen, torsion deflection and protuberant deformation), weights constant tension mechanism, roller institutions and block pin parts were designed.

针对粗电极丝（直径特性（时效弯曲变形、损耗加长、扭转变形和突起变形），设计了砝码恒张力机构、辊压机构及挡销部件。

It is the same as with diameter of the roller to drive the tape.

它用两不梢直径不异的辊来驱不静纸带.

Spinning Test of Big Diameter Spinning Top Roller

大直径细纱胶辊纺纱试验

The roller method can be used in the measurement for a large scale diameter of a workpiece, but the sliding motion of the roller on the workpiece would induce more errors.

滚轮法用于大型工件的直径测量时，由于滚轮和被测工件之间产生的滑失现象造成测量误差较大。

The rolling transmission is driven by a vector frequency motor and floating roller system and PLC can automatically calculate the reel diameter, achieving the reeling tension conical control.

收卷传动采用矢量变频电机、浮动辊系统组成，并通过PLC自动计算卷径实现收卷张力锥度控制；