tension area的例句大全

Sizing efficiency can reach above 85% and loom efficiency can reach 82% by innovating tension area of warping process, adjusting sizing processing route and size formula, innovating sizing method and reed-in method.

通过改进整经工序张力区域划分、调整浆纱工艺路线和浆料配方、改进浆纱及穿筘操作方法，使浆纱好轴率提高到85%以上，织机效率达到82%左右。

For the analysis, the flexural cables were placed along the trace of maxi principal stresses in the pier and anchor block, the concrete was prestressed in the tension area of the pier neck which is connected by the pier with the anchor block.

同时，根据墩体及锚块内的最大主应力迹线进行无粘结弯曲锚索的布置，对以闸墩颈部（闸墩与锚块连接处）为主的受拉区混凝土进行预压。

The structure is that steel tube in the upper section, plain concrete-filled steel tube in the middle section, and concrete filled steel tube column reinforced in compression and tension area in the bottom section.

这种结构形式是从底部到顶部依次为在受压区和受拉区配筋的钢管混凝土、钢管素混凝土、空钢管，截面从下到上递减。

In a certain content scope, with the increasing of the content of NaCl and NaOH, dynamic low interfacial tension curve moves toward low interfacial tension area.

在某一含量范围内，随NaC1或NaOH含量增加，动态低界面张力曲线移向低界面张力区。

Alveolar bone of the compressed area would be absorbed with the last of force and that of the tension area formed, then teeth moved.

正畸牙加力的初期会出现疼痛，随着力的持续，压力侧牙槽骨吸收，张力侧牙槽骨形成，牙齿发生移动。

Compared with those of as-sprayed ring, hardness and tension strength of area near processing face are increased by45% and40% respectively.

靠近压力加工面部位，硬度较沉积坯提高了45%，拉伸强度较沉积坯提高了40%。双向楔压后孔洞闭合、密度硬度分布都比较均匀。

Construction Method of Tension Stringing in Special Area

特殊地段张力放线的施工方法

Several Construction Measures of Tension Stringing in Mountainous Area

浅谈山区张力放线的几项施工措施

But settlement ageing will also be further intensified, and population movement is the main influence factor, this also is of ecological system together with the self-regulation and external tension in the study area.

但聚落老龄化还在进一步加剧，而人口流动是其主要影响因素，这也是研究区生态系统的自我调节和外部拉力共同作用的结果。

The summit was supposed to rubber-stamp a package of measures to settle the tension affecting the euro area, but developments in Portugal have cast a shadow.

这次峰会原本是为了出台相关措施，解决影响欧元区的紧张情绪，但是葡萄牙的事态进展使峰会蒙上一层阴影。

The dynamic dilational properties and the dependences of interfacial dilational modulus, phase angle, elasticity and viscosity on the concentrations and the frequencies were explored using method: the surface tension response to sinusoidal area variations.

具体考察了其动态界面扩张性质及界面扩张参数（模量、相角、弹性、粘性）随表面活性剂体相浓度和工作频率的变化规律。

Spalling cracks resulted from tension failure of concrete in wall joint and adjacent area are primary when the thin wall ( including the wall with visible wide beam) endured out-of-plane moment.

薄墙（包括墙上设有明梁的墙）受梁端施加的平面外弯矩时以墙上节点区与节点附近一定范围的混凝土受拉破坏形成剥离裂缝为主；

Results: The wet weight, protein content, contractive tension and muscle fiber cross-section area of either SOL or EDL in experimental group were obviously increased ( P < 0.05).

结果：实验组比目鱼肌和趾长伸肌的总蛋白质含量、肌湿重、肌张力以及肌纤维截面积均较对照组有显著增加。

This paper introduces a good many factors influencing the moisture-free weight per unit area of warp knitted fabric, measures and theoretically analyzes the fineness of raw material, warping tension, loop length, thermal setting, and so on.

介绍了影响经编织物干克重的诸多因素。对原料细度、整经张力、线圈长度及热定形等影响因素进行了实际测试和理论分析。

It proposes to adopt variable stagger arrangement and to change the horizontal tension link on push-off device into the compression link so as to reduce the deflection of contact wire in area adjacent to mid-point anchor in straight line and in large span length up to 65 m.

提出在直线区段的中心锚结附近和65m大跨距内，采取不等之字值布置法和反定位装置处的水平拉杆改成压管的措施减小接触线风偏。

The tension reinforcement ratio and the aspect ratio of the loading area are two important factors that influence the punching capacity of concrete slabs.

纵筋率及冲切加载面边长比是影响混凝土板受冲切承载力的重要因素。

In this paper, the split-strip discrete method is used to analyse the 3-dimensional deformation and tension distribution of cold rolling strip, By considering the noncontact deformation area, the velocity discontinuity is avoided at the deformation field entrance.

本文采用分条离散法分析冷轧带材的三维变形，求解出前后张力分布。通过考虑入口非接触变形，使变形区入口处不产生速度间断。

According to the deformation of shear spinning on conical workpieces, the stress and strain has been analyzed and the new deformation mechanism has been put forward that the forming area of shear spinning should be divided into tension bending zone and rolling zone.

根据剪旋过程的实际情况进行了应力应变分析，对剪旋变形机理提出了新的见解，将剪旋变形区分为拉弯区和辗压变形区。

When the size of neck was big enough, break occurred at the stress collection area of the cage on the tension side.

而当假体颈部尺寸足够大时（4号），假体的断裂发生在张力侧中空部分融合小孔的应力集中区。

Regular practice will relieve lower back pain and release tension and strain in the upper back and neck area.

规律的练习会释放下背部疼痛，放松上背部和颈部区域。