titanizing的例句大全

Effect of deformation on titanizing process

塑性变形对渗钛过程的影响

Study of Solid Powder Titanizing

固体粉末渗钛的探讨

Titanizing was made in the surface of carbon steel sample.

列举了碳钢试样加弧辉光离子渗钛处理，并对其渗层显微组织、合金成分及相组成进行了分析讨论；

Study on electrode life test for spot welding hot dip galvanized steel by method of surface titanizing

表面渗钛的镀锌钢板点焊电极寿命试验研究

Surface Titanizing and Nickelizing of Copper Using Double Glow Plasma Surface Alloying Technique

纯铜双辉等离子渗钛、镍表面合金化研究

Study on Corrosion Resistance of Graphite Anode by Arc-added Glow Discharge Ion Titanizing

石墨电极加弧辉光渗镀Ti抗蚀性能的研究

Study on Titanizing in Neutral Salt Bath

中性盐浴渗钛的研究

Application of Arc-added Glow Discharge Ion Titanizing to Graphite Anode

加弧辉光渗Ti在石墨电极上的应用

The experimental results show that prior deformation at room temperature accelerates the process of titanizing and there is the optimum deformation region.

根据实验结果分别讨论了温度、时间、形变量对渗钛过程的影响规律，实验结果表明预先室温塑性变形对置换原子钛的渗入有促进作用，存在一个最佳形变量。

Titanizing, Aluminizing and Titanizing-Aluminizing by Solid Power Method

固体粉末法渗钛、渗铝及钛铝共渗的研究

The relationship of the process parameters to the depth of diffusion, concentration of titanium in the diffusion layer and the microstructure of titanizing layer are studied.

探讨了工艺参数与渗层厚度的关系，渗钛层组织特征，渗层钛浓度分布。

The high temperature oxidation resistance of plasma titanizing alloying layer and aluminium alloying layer at 400 ℃ and 700 ℃ after oxidation 100 hours were investigated.

对离子渗钛试样和粉末渗铝试样以及纯铜试样在400℃和700℃高温循环氧化100小时的抗高温氧化性能进行了研究；

A mathematical model for titanizing of steel which can be used in pack or gas titanizing process is given according to Fick's law of diffusive process and tested by the experiment.

本文从Fick第二扩散定律出发，建立了适用于气体或固体渗钛的数学模型，并通过碳钢的固体渗钛实验进行验证。

The result shows that solid powder titanizing without protective atmosphere is available, and the optimal titanizing temperature is at 950 ℃ or so, the optimal titanizing time is 4 hours or so.

结果表明，在无保护气氛下固体粉末渗钛是可行的，但其最佳渗镀温度为950℃左右，最佳渗镀时间为4h左右。

A new brazing technique of ceramic is presented, in which the arc-added glow discharge titanizing is applied to ceramic as a preparative process, then the ceramic is brazed to metal in glow discharge furnace without flux.

介绍了一种陶瓷钎焊的新方法，即以陶瓷加弧辉光渗钛为先导工序，然后在辉光炉中实现陶瓷／金属无钎剂钎焊。

The optimum technological parameters of titanizing and synthesis stage were obtained. The variation laws of phase structure, surface morphology, composition, appearance and micro-hardness of TiN permeation layer were achieved.

找到了渗镀TiN时渗钛阶段和合成阶段的最佳工艺参数，获得了各工艺参数控制条件下TiN渗镀层相结构、表面形貌、表面成分、外观、显微硬度的变化规律。