AXIS的例句大全

Through CNC-PLC data and tache of signal disposals of simulation unit, principal axis AC motors is controlled by transducer. hence, the constant thread speed of grinding wheel combining with the principal axis motor is gained.

采用CNC-PLC模拟量单元的数据及信号处理环节，用变频器来实现对砂轮主轴电机的控制，从而保证砂轮以恒定的线速度进行研磨加工。

In order to analyse the relation of magnetic field distribution out of the axis of a loose helical current with the thread pitch, ratio of length to wide and seat in tube, the method of numerical simulation is adopted.

应用数值模拟方法，分析了疏松型超导螺线管电流轴线外的磁场与螺距、长宽比、管内位置的变化关系。

A shaft with screw thread ( the worm) meshes with a toothed wheel ( the worm wheel); changes the direction of the axis of rotary motion.

螺纹杆与齿轮相啮合；改变轴旋转运动的方向。

Axis intersection, which is required in large-diameter reflector frames and frequency doubling crystal framework of SG-ⅲ range of PV systems, three-axle table, precision centrifuge and some machine tools, is an important precision standard.

轴线相交度是一种重要的精度指标，在神光-Ⅲ靶场光电系统的大口径的反射镜架及倍频晶体框架、三轴仿真转台、精密离心机和某些机床中对其大小都有一定的要求。

This paper states the method of double-row cylindrical roller bearing in the back-bone horizontal axis of three-axle test table. This method can make the swing angle and verticality of three-axle precision angle motion table be both 1 second.

论述了首次采用双列圆柱滚子轴承于三轴台中框水平轴系上，使三轴精密角运动台达到了三个轴摆角1〃、两个轴垂直度1〃的要求。

Chapter 5: The chapter designs for the experiment to check for the precision of system regulation, including the resolution and the repeatability of electrically driven displacement, the angle formed with table-board axis of three-axle revolving table and optical axis of autocollimator.

第五章设计实验，检测系统调整的精度，包括电控支架的分辨率、重复性精度以及系统调整完成后，三轴转台的台面轴和平行光管的光轴之间的平行度。

The results of the study show that the compressed gas spraying from nozzle holes form three-dimensional rotation flow in nozzle interior, and the pressure distribution in general is symmetric on the nozzle axis.

研究结果表明：从喷孔喷出的压缩气体在喷嘴内部形成三维旋转气流，压力分布总体上关于喷嘴轴线对称。

Simulate the lumbar spine front flexion, back extension, and left/ right lateral bending movement in the three-dimensional laser scanner, and the rotation motion in the vertical axis in the mechanical properties of biological materials tester.

在三维激光扫描仪上模拟腰椎的前屈后伸、左右侧弯运动，在生物材料力学特性试验仪上模拟腰椎在纵轴上的旋转运动。

Study on the liquid velocity distribution along the axis of a jet loop three-phase fluidized bed reactor

喷射环流三相流化床反应器轴向液速分布的研究

Brain Emotional Learning Based Intelligent Flight Control for A Variable Thrust Axis Based UAV

变推力轴线无人机的大脑情感学习智能飞行控制

The thrust characteristics of axis symmetry nozzle were mainly measured in test. For the nozzle having a vectoring angle, the deflection efficiency was measured too.

对于轴对称喷管模型主要进行了喷管的推力特性测量，对于实施矢量偏转后的喷管模型除了给出了喷管推力特性外，还给出了喷管的偏转效率。

In the hydroelectric generating set, the thrust bearing under huge axis push is one of the key components which determine whether the unit can be operating safely and reliably.

水轮发电机组中，承受巨大轴向推力的推力轴承，是机组能否安全可靠运行的关键部件之一。

The main structure is the axis, and the secondary structures are positioned as two wings on each side to form the main rooms and yard.

主结构就是轴线，而次要结构则置于每一面的两翼，从而构成主屋和院子。

Thrust Block Renovation of Main Axis and Practice in Operation on AP 6 6 Type Steam Turbines

AP-6-6型汽轮机主轴推力盘改造及运行实践

Coal and gas outburst danger zone is mainly distributed in the southern thrust fault nearby, the eastern syncline axis and the regional of magma intrusion.

在新安矿区南部逆冲断层附近、东部向斜轴部和岩浆侵入严重区域存在着煤与瓦斯突出危险性。

On styles and mechanism of thrust on the south margin of Inner Mongolia axis

内蒙地轴南缘盖层中逆冲断层的样式及形成机制

The internal flow in the mini thrust misalignment nozzle where the inlet flow is not parallel with the axis of its supersonic section is studied.

研究了入流倾斜于喷管超音速段轴线的微推偏喷管内流场。

Thrust misalignment in parabolic nozzle is investigated for the situation where the gas flow is misaligned with respect to the axis of the supersonic region of the nozzle.

研究了当气流偏离抛物型喷管超音速段对称轴时所引起的喷管推力偏心。

Pituitary-Adrenal Axis and Thyroid Dysfunction in Alzheimer' Disease and Multi-infarct Dementia

阿尔茨海默病、多灶性梗塞性痴呆与垂体-靶腺轴功能关系的研究

The PT condylar axis was obtained from an axial slice 8 mm distal to the tibial hyaline cartilage surface.

胫骨髁后缘轴线（PT）由胫骨平台后方内外侧骨皮质表面的连线形成，于胫骨平台关节软骨以远8mm的层面上获得。