CONE的例句大全

Measuring planning target volume margin in kV cone beam CT guided three-dimensional conformal radiotherapy of brain metastases carcinoma

千伏锥形束CT测量脑转移瘤放疗计划靶区外放研究

Control System of New Type Cone and Plate Blood Viscosity Testing Apparatus

新型锥板式血液粘度测试仪控制系统设计

In the high cone voltage analysis, three alkaloids take place main fragmentation. The fragmentation of caffeine and theophylline is easier than that of theobromine.

CONE电压升高后，3个生物碱均发生主要裂解，其中咖啡因和茶碱较可可碱易发生裂解。

Inertia cone crusher is a high-efficiency, super-fine crushing equipment with the unique principle and structure. It can realize "selective crushing" and meet the requirements for "increase crushing and decrease grinding" technological flow sheet.

惯性圆锥破碎机是一种具有独特原理和结构的新型节能超细破碎设备，能实现物料的选择性破碎，满足多碎少磨新工艺的要求。

The bench of experiment consists of two main parts: first, cone-plate viscometer, second, Constant temperature bath.

实验台主要包括两部分：一是锥板式粘度计，一是恒温槽。其他辅助仪器包括特斯拉计等。

The measured temperature of contrast between the testicular cone and the surface of the scrotum were done under identical conditions of the experimental irradiation. Comparison of the results of the groups at different temperature was done to find out the effective temperature threshold for contraception by microwave.

本文在相同的实验照射条件，和用睾丸中心与阴囊表面同时进行对比性测温的情况下，对实验规定的不同温度组动物的实验结果进行比较，目的在于探讨微波用于节育时的有效温度阈值。

It consists of two blackbody furnaces with an isothermal convex-inward cone cavity, a double-beam infrared spectrophotometer with a double-grating and a nine-point cyclic temperature control equipment.

本装置由两台等温内凸锥空腔黑体炉、一台带水冷观察窗的旋转样品炉、一台双光束光栅红外分光光度计和一台九点循环控温仪组成。

A comparison test of selected solid cone nozzles with spiral nozzles has been carried out, the variation rule of atomized particle size and distribution rule of atomized particles for swirl nozzles being systematically studied.

选择实心锥喷嘴和螺旋喷嘴进行对比试验，系统地研究了旋流喷嘴的雾化粒径变化规律和雾化粒度分布规律。

On the basis of compression test of a thin-wall cone tube sample of molded pump material, an inverse problem of identifying the elastic constants of molded pulp material is discussed by making use of finite element analysis and digital image correlation method ( DICM).

基于纸浆模塑薄壁圆锥筒的压缩试验，讨论了可以利用有限元分析和数字相关测量方法（DICM）来识别纸浆模塑材料弹性常数的逆问题。

Four groups of site contrast tests are chosen to conduct the systematic site soil tests including the plate load test, spire plate load test, flat dilatometer test, standard penetration test and static cone penetration test.

选定4个研究场区地基土，进行现场系列原位土工试验，即平板载荷试验、螺旋板载荷试验、扁铲侧胀试验、标准贯入试验、静力触探试验；

The simplified formula of ultimate tension load is obtained in view of mix plastic-cone tension failure mode of the M10 plastic embedded part.

针对M10型预埋件的塑胶-锥体复合拉伸破坏形态，得出极限拉伸荷载的简化计算公式。

Meanwhile, a useful value for following study on tensile fracture mechanism of UHMWPE/ LDPE is given. The simplified formula of ultimate tension load is obtained in view of mix plastic-cone tension failure mode of the M10 plastic embedded part.

对后续研究UHMWPE/LDPE复合材料声发射特性和拉伸破坏机理具有参考价值。针对M10型预埋件的塑胶-锥体复合拉伸破坏形态，得出极限拉伸荷载的简化计算公式。

The concrete measures such as adjusting radial winding density, assuring the starting position of cone drum belt, configuring tension exchange gear reasonably to adjust the roving tension were proposed.

并提出同时应采取调整轴向卷绕密度、确定锥轮皮带起始位置、正确配置张力变换齿轮等具体措施直接对粗纱张力进行工艺调整。

In the upsetting technology theory, a tension stress theory of a rigid-plastic mechanical model and a shearing stress theory of a hydraulic stress mechanical model are proposed for upsetting a cylinder between flat platens, and a new type technology for upsetting between cone-platens is advanced.

在镦粗工艺理论方面，提出了圆柱体镦粗的刚塑性力学模型的拉应力理论和静水应力力学模型的切应力理论，设计了锥形板镦粗的新工艺。

Rods, cones, and apoptotic cells were labeled by antibodies of anti-rod and anti-cone cells, and terminal deoxynucleotidyl transferase dUTP nick-end labeling ( TUNEL), respectively.

抗视锥和抗视杆细胞的抗体分别标记视锥和视杆细胞，dUTP缺口末段标记法（TUNEL）标记凋亡细胞。

Numerical simulation analysis of 220 kV cable terminal stress cone in force field

220kV电缆终端应力锥在力场中的数值模拟分析

The operation principle and structure features of a 220 kV cable terminal stress cone were simply described. The numerical simulation model of the cable terminal structure was proposed.

应用220kV电缆终端的结构型式和工作原理，建立了该种电缆终端结构的数值仿真模型；

It is the show that the influence of structure forms and rubber property on 220 kV cable terminal stress cone is very obviously. The suitable structure form and relatively rubber property should be chosen in engineering design.

结果表明：橡胶材料及其结构形式对220kV电缆终端应力锥应力分布的影响十分明显，实际工程设计中应选择适当的橡胶材料及相应的结构形式。

During development 220 kV cable terminal, the stress distribution of the rubber stress cone is the key problem.

在220kV交联电缆附件开发过程中，橡胶应力锥的压力分布状态是要解决的关键问题。

FEM analysis of the electric field in the condenser cone termination of power cables

电力电缆电容锥式终端电场的有限元分析