GB的例句大全

By referring to the acceptance test specification for LAN systems GB/ T21671-2008, communication network testing items and testing methods in digital substation are proposed.

从数字化变电站的实际出发，参照局域网验收测评规范GB/T21671-2008，提出了数字化变电站通信网络性能测试的具体项目，并给出了具体的测试方法。

On National Standards ( GB) Specifications and Bench Test Method for Wheeled Tractor Mechanical Steering Gear

轮式拖拉机机械转向器技术条件和台架试验方法标准的制定

The practical operation shows that the effluent quality from the pretreatment/ AO process treatment system has reached the first class criteria specified in the National Discharge Standard of Pollutants from Textile and Dyeing Waste water ( GB 4287& 1992).

染料生产废水的电解工艺处理方法实践表明，预处理/AO工艺的出水水质达到了国家《纺织染整工业水污染物排放标准》（GB4287&1992）中的一级标准。

We established a quantitative determination method for GB, GD and VX by CIC. The relative error was calculated.

运用GC-AED特有的化合物无关校正曲线法（CIC法），建立了GB、GD、VX CIC定量测定方法，计算出了各种方法的相对误差，总结了CIC法的误差规律；

With the simple model, some examples are shown to compare the provisions for minimum shrinkage and temperature reinforcement in GB 50010-2002 Code, ACI 318-02 Code and AS 3600-1988 Code. Finally, some recommendations are proposed.

利用该模型，通过算例比较了中国GB50010-2002、美国ACI318-02、澳大利亚AS3600-1988三国规范关于混凝土板温度收缩钢筋的最小配筋率要求，并对此提出了设计建议。

The related regulations of temperature rise test of autotransformer for autotransformer starter in IEC, GB were described, the current in every winding of autotransformer was analyzed.

叙述了IEC和GB标准中对自耦减压起动器中自耦变压器温升试验的有关规定。

The properties at elevated and room temperatures obtained by tempering withholding time of 1 hour can meet the requirement of the standard of GB 5310-85.

回火保温1h的高温性能、常温力学性能均达到国标GB5310－85标准要求。

The results indicated that for GB/ PP composites, with the increase of the GB content, the tensile modulus, bending strength and modulus increased linearly, while the yield strength decreased slightly;

结果表明：随着GB用量的增加，单、双螺杆挤出GB/PP复合材料的拉伸模量、弯曲强度和弯曲模量均呈线性增长的趋势，而屈服强度则有小幅下降；

For GB/ LLDPE composites extruded by single screw extruder, with the increase of filler content, the tensile modulus, bending modulus increased linearly, while the yield strength and bending strength increased slightly at higher filler content.

而GB/LLDPE中，随着GB用量的增加，单螺杆挤出复合材料的拉伸模量、弯曲模量均呈线性增长趋势，而屈服强度和弯曲强度在含量较高时略有上升；

The teratogenic test of GB was carried out in wistar rats.

我们用wistar大鼠进行了GB的致畸胎试验。

The Teratogenic Test of GB

GB的致畸胎试验

On the basis of method of controlling classical V-belt drives pretension under state standard GB/ T 13575.1-92. a calculating formula of determining test load G is deduced.

针对GB/T13575.1-92中控制、测定普通V带传动初拉力F0的方法，推导出确定测量载荷G的计算公式。

The standard code is changed from FZ/ T ( industry standard) to GB/ T ( national standard).

标准代号变化，由原来的行业标准上升为国家标准。

GB: So what did you feel like when you were asked to join as the lead guitarist?

那当时你被邀请做主音吉他的时候那感觉是什么样的呢？

Based on optical time division multiplexing technology, 5 Gb/ s soliton transmission is successfully carried out by using fiber ring laser as the optical source.

利用光纤环激光器作为孤子源和光时分复用技术成功地进行了5Gb／s的孤子传输实验。

Experiment on 2 × 1.244 Gb/ s Optical Time Division Multiplexed System

2×1.244Gb/s光时分复用系统的研究

By using optical fiber as optical delay timer and stretching fiber in high temperature to adjust delay time precisely, a 2 × 1.244 Gb/ s all optical time division multiplexed experiment system is completed, which meets the requirements of synchronous transfer mode ( STM).

使用光纤作延迟器，利用高温熔融拉伸法微调延迟时间，完成了2×1.244Gb／s全光时分复用系统，满足了同步传输模式的要求。

According to GB/ T 18510-2001, by the method of comparing with reference matters, the authors carry out t-test and F-test for the measurements of nitrogen in coals by high temperature combustion thermal conductivity cell detector.

运用GB/T18510-2001中与标准物质相比较的方法对运用高温燃烧热导池检测法测定煤中氮的结果进行t-检验和F-检验，证明该方法完全符合GB/T476-2001中对氮元素测定的要求。

This paper gives the suggestions for clauses on thermal limiting output, accuracy class, temperature rise of electromagnetic unit, short circuit withstand capability and ferro-resonance in the standard of GB/ T4703.

提出对GB/T4703标准中热极限输出、准确度、电磁单元温升、承受短路能力和铁磁谐振条文的修改意见。

Research and Implementation of Mould GB Parts/ Components Library

模具国标零件库与组件库的研究与实现