angle head的例句大全

Liquid forging processing to thin wall waveguide angle head has been experimentally studied.

本文对簿壁波导弯头件的液态模锻成形进行了研究。

Then I dared to lift my camera carefully from my belly and estimate an angle of a shot, and then I made several pictures across my head.

然后，我勇敢地小心地从腹部举起了相机，估计了拍摄的角度，当时我越过我的头拍了几张照片。

According to the practical issues encountered in boiler inspection the stress analysis method is applied in analytic error calculation of small end of conical head with half top angle> 60 °. Analytic checking calculation shows that error is in allowance range.

针对在锅炉检验中常遇到的实际问题，应用应力分析法，对半顶角大于60°锥形封头的小端解析误差进行了计算分析，并经解析式验算，指出其误差在工程允许范围内。

The top view at which lateral epicondyle of the humerus showing mini-triangulum and the anterior surface of the distal humerus articulation with the forearm being shaded is more simple, faster and precise for the volume rendering technique measuring the humeral head retroversion angle with multi slice spiral CT.

俯视位观察肱骨，当外上髁露出呈小三角形、肱骨远端前关节面被肱骨头遮盖重叠的位置是多层螺旋CT三维重建测量肱骨头扭转角的更简单、更快捷而且准确的测量位置。

Research of Erasing Round Head of Plate by Small Angle Rolling

微角轧工艺消除钢板圆头的研究

Influence of articular surface diameter of the humeral head in volume rendering technique measuring the humeral head retroversion angle with multi-slice spiral CT

肱骨头关节面直径对多层螺旋CT容积再现技术测量肱骨头扭转角的影响

Methods 10 patients ( 9 were congenital and was traumatic) of SOP with marked compensatory head posture ( the tilting angle degree of head toward the uninvolved side was ≥ 20 °) were performed Harada& Ito procedures.

方法对10例（先天性9例，外伤性1例）头位倾斜严重（向麻痹眼对侧肩倾斜≥20°）的上斜肌麻痹患者施行Harada&Ito手术。

The allowable settlement of pile head is suggested and vertical pile can bear load with inclination of less than 10 °, and batter pile bearing vertical load can be angle of less than 10 °.

以桩顶沉降控制作为桩基承载力设计的标准，认为直桩可以承受小于10°倾角的倾斜荷载，承受竖直荷载的斜桩可以有小于10°的倾角。

Projecting from the further angle of the room stands a dark-looking den-the bar-a rude attempt at a right whale's head.

在堂屋的远角里，有一间突出的昏黑的幽室…酒吧…粗具一只露脊鲸头的形状，就算它象个鲸头吧。

In that tournament, Ronaldo was not just the complete center forward, striking with either foot or head from any angle, any half-chance.

在那届世界杯上，罗纳尔多不仅仅是简单意义上的前锋，它可以左右脚射门或可以从任何角度任以何看似不太可能机会头球攻门。

Application of Supine Position with Head Deviation in Surgery of Cerebellopontine Angle

头偏侧仰卧位在桥小脑角显微手术中的应用

Method The relatively used side between the two neutral zone was found by neutralizing bilateral head torsion angle with prisms.

方法对14例存在两个反方向中间带的先天性冲动性眼球震颤患者，采用三棱镜中和两侧代偿头位扭转角的方法确定两个中间带中起主导作用的中间带后，配戴三棱镜；

Winston dared not turn his head even by a millimetre, but sometimes her livid, gasping face came within the angle of his vision.

温斯顿的脑袋一动也不敢动，但是有时她的紧张、憋气的脸进入到了他的视野之内。

The calculating result showed that impeller outlet diameter D2 effects on the head largest of these parameters, vane outlet angle β 2 smallest, inlet diameter D1, outlet width b2, vane number Z and vane length ratio R were between them successively.

计算结果表明，在这些几何参数中，叶轮出口直径D2对扬程影响最大，叶片出口角2β影响最小，进口直径D1，叶轮出口宽度b2，叶片数Z和叶片长度比R依次地处于它们之间。

The FTE SAMs was characterized by the time-of-flight secondary ion mass spectrometer ( TOF-SIMS), atomic force microscopy ( AFM) and contact angle measurement, and the tribology properties of the FTE SAMs were measured by the Olympus head/ disk interface reliability measurement system.

应用时间飞行二次离子质谱仪（TOF-SIMS）、原子力显微镜（AFM）和接触角测量仪对FTE自组装膜进行表征。通过Olympus磁头磁盘界面可靠性测试系统对FTE自组装膜的摩擦学性能进行研究。

Test results show that the flow regime is good in a head tank with a greater length of the outlet pond and a smaller contract angle, while the sediment deposition is heavy.

试验结果表明，出水池长度较长，收缩角较小的高位井中的水流流态较好，但池内泥沙淤积程度较重。

Process and method to solve the problem of retarded material in the extruder during production by way of improving taper angle of screw head, connector flange and structure of perforated plate are presented.

介绍了通过改进螺杆头锥角、连接件法兰以及多孔板结构以解决挤出机生产过程中滞料问题的办法。

to practice the proper brush stroke, hold the toothbrush head (without any toothpaste on it yet) at a 45-degree angle toward your gums.

开始练习正确的刷牙方式，保持刷头（上面还没有牙膏）与牙龈成45度角。

rotary angle of vertical milling head

立铣头回转角度

wheelbase, head tube angle, fork rake [slidable dropouts], boom length and height [2 bb shells], and seat height.

轴距，头管角，叉耙[slidable辍学生]，臂长度和高度[2体弹]，和座位的高度。