bending deflection的例句大全

Integration Matrix Method for Calculation of Bending Deflection

弯曲挠度计算的积分矩阵方法

Inland Vessel External Force Calculation with the Correction of Bending Deflection

内河船舶考虑弯曲挠度影响的外力计算

It gave the detail about analyses of bending deflection and strength, compared the results with other methods.

在此基础上，详细分析计算了梁的弯曲变形和弯曲强度，并与采用其他方法得到的结果进行了比较。

It is difficult to get a proper practical answer of bending deflection for H-Beam roller straightening.

型钢辊式矫直压弯挠度的计算一直难于得出适用工程的解.

A New Method to Solve the Bending Deflection of Stepped Beams

阶梯形变截面梁弯曲变形的一种新解法

In this paper, the Laplace transform method is used to derive a general solution of the deflection curve equation for a step beam under the action of arbitrary complicated loading conditions. This result provides a convenient way of analysing the bending deflections for the step beam.

本文采用拉昔拉斯变换法导出了复杂加载情况下阶梯形梁的挠曲线方程的通解，为分析阶梯形梁弯曲变形提供了简便方法。

The ultimate failure mode of the experimental model is overall bending failure. The specific process is the buckling of the bottom chords, redistribution of internal force and the large deflection.

试验模型结构最终的破坏模式为整体弯曲破坏，具体过程表现为下弦杆屈服，内力重分布，挠度过大。

Solutions of basic equations including bending moment, shearing force, lateral deflection and rotation of the wall axis are given.

给出了墙轴弯矩、剪力，侧向位移和转角的基本方程及其一系列解。

Basing on the elastic bending theory of beams in large deflection, the non-linear shearing behavior of cellular materials under large deformation is studied in the paper.

将梁的弹性大挠度弯曲理论应用于蜂窝壁板，研究了大变形条件下蜂窝材料的非线性剪切变形行为。

Some elastic curved surface differential equations and neutral planes of circular piezoelectric composite laminates are derived from the elastic thin plate bending theory with small deflection.

应用小挠度弹性弯曲理论，导出圆形压电复合层薄板的弹性曲面微分方程和复合层薄板的中性面位置方程；

Also the three bending moment equivalent equation of multispan multidiameter beam and its equivalent equation of deflection curve are reasoned out, according to the relationship among deflection of simple beam, relative deflection and rotating angle of the cross area of support base.

其次利用简支梁挠度，相对挠度及支座截面转角的关系，推导并建立阶梯连续梁的三弯矩等效方程及其挠曲线等效方程。

In this paper, the elemental stiffness matrix of a rotating twisted and tapered beam, due to deformation of axial direc-tion, bending and shearing including shearing deflection and rotation effects, is studied.

本文研究了在剪切变形和转动的影响下，在轴向变形、弯曲变形和剪切变形的作用下的旋转变截面扭梁的单元刚度矩阵。

It is a difficult work to calculate the deflection of filament wound tapered tube at bending because of changing layer thickness in every cross section.

纤维缠绕的锥形管，由于各截面的纤维层厚在不断变化，弯曲变形计算比较困难。

According to the transferring matrix method, the paper presents a method for calculating the deflection of a filament wound tapered tube at bending and the calculation result is proved by experiment results.

本文以传递矩阵法为基础，计算纤维缠绕锥管在弯曲载荷作用下的挠曲变形，并以实验结果验证了计算结果。

maximum load and its deflection and stiffness for three-point bending specimens of brittle materials

脆性材料三点弯曲试样的最大荷载及其挠度和刚度

maximum load and its deflection and stiffness for three-point bending specimens of brittle materials

脆性材料三点弯曲试样的最大荷载及其挠度和刚度

find the value of the bending stress and the deflection at the center if the ribs are omitted.

如果略去肋条，求中心处的弯曲应力和挠度之值。

In the analysis of plates in bending, deflection is obtained by solving Eq.

在受弯板的分析中, 借求解满足板边界处条件的方程得出挠度.

Results show that: ( 1) In the bending process of the I-shaped structural beams of bamboo, the axis of symmetry of the deflection value in the middle and both sides are diminishing symmetrical distribution, the deflection value of hinged fulcrum position is essentially unchanged.

结果表明：（1）竹质工字型结构梁受弯过程中，竹质工字型结构梁挠度值以中间为对称轴两侧呈递减对称分布，两端简支点位置的挠度值基本没有变化。

Determination of the long-term ultimate bending strain and calculation of the long-term ultimate relative ring deflection, both under wet conditions

潮湿条件下长期环状弯曲应变和长期环形偏转的极限测定