bending strain的例句大全

Reduced integrated quadratic shell element S 8 R 5 can provide accurate solution for small strain membrane bending problem.

减缩积分二次单元S8R5对于小应变薄膜弯曲问题的模拟能给出精确解.

Testing method for annealing point and strain point of glass by beam bending

玻璃退火点和软化点测定方法-压梁法

It is investigated that the influence of Bauschinger Effect on yield strength of tube body by using four point bending test to simulate the tube making process at varying stress strain amplitudes.

采用X65钢板在四点弯曲加载条件下，模拟输油管制管过程中不同应变量下的应力&应变过程，研究包申格效应对输油管管体屈服强度的影响。

Strain Damage Failure Analysis and Prediction for Beams under Pure Bending Loads

纯弯曲梁的应变损伤失效分析和预测

testing method and influence factor for hot bending stress-strain relationship of refractories

耐火材料高温弯曲应力-应变关系测试方法及影响因素

According to the deformation of shear spinning on conical workpieces, the stress and strain has been analyzed and the new deformation mechanism has been put forward that the forming area of shear spinning should be divided into tension bending zone and rolling zone.

根据剪旋过程的实际情况进行了应力应变分析，对剪旋变形机理提出了新的见解，将剪旋变形区分为拉弯区和辗压变形区。

In the method the modal strain energy of an element is divided into tension modal strain energy, torsion modal strain energy and bending modal strain energy.

该方法将单元模态应变能分解为拉压、扭转和弯曲模态应变能，利用单元的主要模态应变能分量与结构固有频率的改变量对结构裂纹位置进行识别。

The distributions of stress and strain ahead of a precrack tip in three point bending specimen are calculated by finite element method and the fracture surfaces, the micro-cavities and micro-cracks in the vicinities of the precrack tip are also observed.

对三点弯曲预裂纹试样断口形貌、裂尖附近微孔及残留裂纹进行了观察，并用有限元方法计算了裂尖应力应变场。

When three point bending test was made under the 300N compressive force, the maximum tensile strain was at the medial point of middle femur, average 1.18E~ 03 ( mm/ mm).

三点弯曲在300N压力时，股骨中间1/2端，内侧点为最大张应变，平均值为1.18E-03（mm/mm）。

Three-point bending model considering strain gradient effects& part ⅰ: propagation of tensile localized band

考虑应变梯度效应的三点弯梁模型解析研究&第一部分：局部化带的传播

Plane Strain Fracture Toughness Testing by Three-Point Bending

用三点弯曲试样测试平面应变断裂韧性

The experiments of obtaining stress strain curves in cyclic loading condition are investigated, and the measure-ments of the stress strain curves in reverse loading by using sheet metal compression test and three-point bending test are clarified.

对材料在循环加载条件下应力应变曲线的实验获取方法进行了探讨，重点介绍了板料压缩、三点弯曲实验确定材料反向加载应力应变曲线的原理和方法；

A four point bending device was used to investigate the effect of stretching on osteoblasts collagen production. Cells were stretched with different strain level and loading time.

使用四点弯曲加载装置研究机械拉伸对成骨细胞胶原合成的影响，在生理应变范围（500～1500με）研究了不同加载时间、不同应变水平对成骨细胞胶原合成的影响。