brazed的例句大全

In this paper, Be and HR-1 stainless steel were bonded by brazed and diffusion bonded.

另一方面利用有限元方法模拟了铍与HR -1 不锈钢扩散焊区的浓度分布,模拟结果对合理制定工艺具有指导意义.

Local fusion deformation occurred after the product antenna combination was brazed.

某产品天线组合钎焊后,局部发生熔化变形现象.

In this paper, each forming operation during quadruple-wall curly brazed tubes'forming processes was summarized.

综合阐述了四层卷焊管成型过程中的各技术环节.

Assemble parts to be brazed.

组装准备铜焊的部件.

The brittleness of brazed seam for nickel-base brazing filler metals is always paid close attention.

镍基 钎料的钎缝脆性问题,一直是人们关注的研究课题.

The theoretical calculation of brazed rate based on C-scan image is described.

利用超声无损检测C扫描图像,可以反应钎焊缺陷及其分布特征,并自动计算出钎着率.

Radio frequency ultrasonic technique for metal brazed high-density honeycomb structures and defect recognition are described.

利用射频超声技术检测大密度金属钎焊蜂窝构件及缺陷识别技术.

The cause of externally applied pipe load to brazed aluminum heat exchanger and the necessity of calculating allowable pipe load are analyzing.

分析了板翅式换热器封头接管外载荷产生的原因和进行许用接管载荷计算的必要性。

Calculation Method of Allowable External Pipe Load Applied to Brazed Aluminum Heat Exchanger Header and Its Application

板翅式换热器封头许用接管外载荷计算方法及应用

Research on ultrasonic imaging NDE of thin electric switch contact brazed quality

薄型开关电触头钎焊质量超声成像无损评价研究

Research on the method for calculating allowable external pipe load applied to brazed aluminum heat exchanger based on limit analyse

基于极限分析的铝板翅式换热器封头许用接管载荷计算方法研究

Analysis of the microstructure of the electron beam brazed joint

电子束钎焊接头组织分析

Microstructures characteristics and properties of solidified aluminum alloy brazed joint

铝合金钎焊凝固接头的组织特征和性能

Analysis of transformation-diffusion brazed joint

相变-扩散钎焊工艺焊接接头缺陷分析

Study on Interface Fracture Mechanics of Brazed Joint

钎焊接头界面断裂力学试验研究

Further research shows that element Mg in 6063 is the main cause making the flux ineffective and the quality of brazed seam degraded.

进一步的研究指出：6063铝合金中的合金元素Mg是使钎剂失效和恶化钎缝质量的主要原因。

The shearing strength of the brazed joint can be also greatly strengthened.

同时还可以显著提高钎焊接头的抗剪切强度。

Cut through the brazed seam on the connection to the side section with the parting grinder.

用分离打磨机切断连接到侧面部件的铜焊缝。

The Influence of Brazing Metal on Residual Stresses in Brazed Joints of Ceramic-metal

钎料对金属/陶瓷钎焊接头残余应力的影响

The brazing-ability and quality of brazed seam of 6063 aluminum alloy brazed by Al-Si eutectic filler metal and QF flux is discussed by means of test of spread-ability and test of T joint.

本文用平百铺展试验和T型接头试验，研究了6063铝合金采用AI－St钎料和氟化物钎剂（QF钎剂）钎焊时的钎焊性和钎缝质量。