contact area的例句大全

Other causes include the out-of-tolerance of blade chord width between adjacent blades, the undersize contact area of serrated working side and the local wearing of non-working side.

而相邻原机件叶片弦宽尺寸超差，锯齿形工作接触面积小，以及非工作面局部碰磨，是引发故障的次要因素。

Large contact area and low surface pressure.

接触面积大，面压小。

The key factors effecting Q_ eff include the number of particles contacting with heating wall, contact time, and contact area.

有效传热系数主要受与加热面接触的颗粒数目、接触时间、颗粒加热面间接触面的大小等因素的影响；

the superhydrophobic carbon/ silica composite films agreed with the complex water contact angle theory of cassie model. the water contact angle was up to 162.5 ° as the actual contact area consisted by 4.26% of solid surface and 95.74% of air bed.

超疏水碳/二氧化硅复合薄膜符合Cassie复合接触角理论，当接触角达162.5°时，固体表面所占的比例为4.26%，而空气所占的比例为95.74%。

Conclusions: There is a normal contact area between the inner surface of lateral femoral tendon and lateral femur condylar to reduce the contact pressure of the lateral surface of patella.

结论：①在正常情况下股外侧肌腱内面与股骨外侧髁存在着接触，这可能是缓解髌骨外侧关节软骨面压力的正常接触；

Then the hazard zone of tire/ rim contact area with axial force of cord, Mises stress, shearing strain and strain energy potential were analyzed.

同时运用帘线轴力、Mises应力、剪切应变、应变比能4个力学量对胎圈部的危险区域进行了精细分析。

It is shown that, static load has evident effects on stress of tire cord in ground contact area;

结果表明，静负荷对轮胎接地区域内帘线受力影响显著；

The model was valid and reliable because the pressure distribution at the tire ground contact, the tire ground contact area and shape were in accordance with those reported in the previous papers.

轮胎接地压力分布、接地面积及形状在趋势上与文献报道的一致，说明此模型有效可靠。

Analytical theory and computational method of contact area and cutting volume of PDC bit cutters

PDC钻头切削齿工作区域及切削量的分析理论和计算方法

The contact location, contact area and stress distribution of the patellofemoral joint were tested with the Fuji pressure sensitive film and the dyeing method in eight fresh human cadaver knee joints under the states of variety Q-angles and knee flexion angles.

本研究应用染色法和压敏片法，对8例新鲜尸体膝关节在不同Q角和屈膝角度时的髌股接触部位、面积和应力分布进行测试。

At a 6 mm step-off with 00 of flexion, the valgus angle increased an average of 7.60, and average contact pressures and maximum contact pressures increased an average of 208% and 97% respectively, and contact area decreased an average 33%.

在屈膝0°，关节面塌陷6mm时，外翻角度平均增加7.6°，平均接触压力和最大接触压力分别增加208%和97%；而接触面积则减少33%。

The remained contact area in the center of the tip surface help to maintain satisfactory weld quality.

电极头中部残存接触区的存在有助于维持较好的焊接质量。

The analytical results show that the solder material, contact area and processing quality of solder layer will be main factors restricting the ability of thermal dispersion for flip-chip configuration LEDs.

研究表明，焊接层的材料、焊接接触面的面积和焊接层的质量是制约倒装焊LED芯片散热能力的主要因素；

The power calculation methods of three-roll planetary mill by using cone rolls are discussed. A series of formulas, including the deformation zone, contact area, rolling force and rolling torque, are presented for practical use.

论述了三辊行星斜轧机利用锥形轧辊轧制时的力能参数计单方法，包括变形区形状、接触线方程、接触弧长和接触面积，以及轧制力、轧制力矩的理论计算和数学模型。

The design for inlaid pieces, rotation contact piece and rotation mechanism is the key points for design, so as to assure every time of press on the switch key cap, the contact spring piece to turn 45 ° to enter into next contact area.

嵌件的设计，旋转接触片和旋转机构的设计为设计的关键。保证每揿压一次开关键帽，接触簧片旋转45°进入下一接触区。

The finite element model of wheels sliding on the rails and rolling process are established by large-scale finite element software ANSYS. Establish contact using the contact element method in the wheel-rail contact area.

主要应用大型有限元软件ANSYS分别建立车轮在钢轨上滑动和滚动过程的有限元模型，在轮轨接触区利用接触单元法来建立接触。

So far, the main method to increase the hemocompatibility of blood pump is to reduce the erythrocyte damage and the contact area. From 1997 to 1999, we developed a spiral blood pump.

减少红细胞破坏和减少血液接触面积是目前可以提高血泵血液相容性的重要手段，为此我们1997年到1999年间研制了叶片为螺旋型且与血液接触面积小的螺旋血泵。

Via analysis of different plate thickness combinations of equality height spacer plate group, contact stress curves and contact area distribution among the plates were got.

对整体高度恒定的垫板组的不同板厚组合进行分析，得到了不同组合时各层垫板间的接触应力曲线，并统计了各个接触层间的接触面积。

The real-time forces and deformations of tire are recorded, and the shape and contact pressure distribution of tire contact area are measured by Prescale films.

实时记录了试验中轮胎受力与变形关系，并采用压力敏感膜测量了轮胎接地区域内的压力分布状况。

It is different from under point contact that there is no stick area under line contact in the partial slip regime, and load distribution within line contact area is uneven due to roughness of surface.

磨痕分析表明，承载区域接触不均匀，存在虚接触区域，其大小与表面粗糙度有关，而接触区域没有不磨损的粘着区，不同于点接触形式。