converter process的例句大全

Study on the New Process for Treating Copper Converter Dusts

铜转炉烟尘选冶联合处理新工艺研究

Study on process of refining high carbon steel in converter

转炉冶炼高碳钢的工艺研究

this paper minute folds and summarizes converter is lowing wind pressure or stop wind, turn the existent problem in process voluntarily.

本文分析、总结了转炉在低风压或停风时，自动转动过程中存在的问题。

Analysis the Problems of Increase Pig Iron Charge on Converter Smelting Process& Its Controlling Methods

提高转炉生铁比问题分析及控制措施

This paper analysed various problems of the Applications of high voltage frequency converter on expand drier from all the process of project management, raised the solving scheme, summarized the actual effect and remaining problems.

从项目全过程管理的角度，系统分析了高压变频技术在本厂SBS后处理膨胀干燥机调速用中的各种问题并提出解决方案，最后总结了新系统建成后的实际运行效果和遗留问题。

Because of utilizing high-speed optoelectronic converter and flash sample technique, the system can process Moir é signal with wide frequency range.

由于采用了高速信号处理和闪烁采样技术，采用该方案的系统能处理宽动态范围的莫尔条纹信号。

Structure and configuration of process control computer system for converter in the Second Steelmaking Plant of Baosteel Branch are introduced.

结合江阴兴澄钢铁有限公司电炉车间介绍了过程计算机对电炉炼钢控制的内容和过程，并对此提出改进的措施。

Process practice on hard wire steel with high carbon from converter

转炉生产高碳硬线钢的工艺实践

Turning motor converter on a engine lathe equiped with tailstock of hydrostatic quill can improve the surface finish to 7-8. The paper introduces the construction of the tailstock and the machining process of the bore.

在普通车床上采用静压尾架车削电机换向器，可以提高光洁度约1.5级，达7～8。文中介绍了静压尾架的结构，尾架孔加工工艺。

Development of Technique Process of Steel Tap hole Integral Sleeve Brick for Converter

转炉出钢口套整体袖砖工艺技术开发

a combination module of matching software and jointly working process of engine and hydraulic converter is presented.

介绍了发动机与液力变矩器共同工作过程和匹配软件的组成模块。

development of technique process of steel taphole integral sleeve brick for converter

转炉出钢口套整体袖砖工艺技术开发

The causes of excessive high oil temperature in practical work process of torque converter of loader.

分析了装载机液力变矩器在实际工作过程中油温过高的种种原因.

The finite element software of simulating the working process of catalytic converter is developed.

开发了催化转化装置工作过程有限元模拟软件.

A Buck, Voltage-Mode DC-DC Converter operate in heavy load is designed based on csmch 0.5μ standard CMOS process.

本文最终设计了基于csmch0.5μm工艺 的Buck结构 、 电压模式控制、工作于重载下的DC -DC 转换器系统.

The working principle and process of converter gas cleaning system-tower & venturi system for No.

介绍了转炉煤气的塔文净化工作原理和工艺流程,同时也对 塔文 系统的主要设备组成作了介绍.

The analog-to-digital converter transforms the incoming real-valued process signals into their digital equivalents.

模数转换器,用于将输入的真实过程信号转换成对应的数字信号.

The L. D. Process uses a top-blow oxygen converter lined with heat-resistant brick.

L. D. 炼钢法使用炉内砌有耐火砖的氧气 顶吹 转炉.

Working principles of Buck chopper for regulating circuit and LCC series-parallel resonant circuit in the CCM work mode were analyzed using the fundamental wave analysis method, and the converter steady state model were deduced as well as the detailed design process and calculation method.

针对Buck调压电路和LCC串并联谐振电路在CCM工作模式下，分析其工作原理，采用基波分析法推导变换器稳态模型，给出详细的设计计算方法。

The L . D . Process uses a top-blow oxygen converter lined with heat-resistant brick.

炼钢法使用炉内砌有耐火砖的氧气 顶吹 转炉.