curing的例句大全

In addition, single leaf weight, leaf density and thickness of tobacco leaves cured in bulk curing barn were bigger, whereas, percentage stem, balanced moisture content and tensile breaking strength were smaller.

另外，密集烤房烤后烟叶单叶重、叶质重与厚度较大，而含梗率、平衡含水率与拉力较小。

Experimental results show that with crisscross winding method and 30% to 40% of resin content and 150 N to 200 N of winding tension for a fiber strand and GPC chart analysis to determine curing time, better comprehensive performance of the composite materials can be obtained.

结果表明：采用交替铺层方式缠绕成型，含胶量控制在30%～40%（质量分数），缠绕张力控制在150N～200N，采用GPC谱图控制固化时机，得到的复合材料综合性能较好；

Curing Behaviors and Properties of Ternary Polymerization Modified Phenolic Resin

基于酚醛三元聚合体系的固化行为及性能

The curing reaction of hydrogenated terpinene maleic anhydride ( HTMA) with bisphenol A epoxy resin was investigated by FT-IR spectrum, and the curing degree, gelation time and its affecting factors were analyzed.

采用FT-IR光谱研究了氢化萜烯马来酸酐（HTMA）与双酚A型环氧树脂的固化反应过程，并分析了固化度、凝胶时间及其主要影响因素。

This paper introduces manufacturing process and curing method of the concrete test block for measuring compressive strength and antiflex cracking strength, expounds measuring and calculation methods and standards of concrete strength.

介绍了混凝土抗压强度和抗折强度试件的制作过程、养生方法，论述了混凝土强度的测定、计算的方法和标准。

Coil coatings was thermal analyzed and researched with DSC in order to test glass transition temperature ( Tg) of the paint film at the maximum precoated metal temperature ( PMT) and determine the optimal curing conditions of different coil coatings.

采用DSC进行卷材涂料热分析研究，测试在不同PMT（最高金属板温）下漆膜的Tg，以确定各种卷材涂料的最佳固化条件。

Application of vacuum tumbling enabled to shorten the curing from 20 hours to 4 hours, saved pickling liquid, reduced labor intensity and increased economic efficiency. 3.

应用真空滚揉技术可使风鹅的腌制时间由原来的20h缩短至4h，并可节约大量的腌制液，降低劳动强度，节约成本，提高经济效益。

Low temperature and high vacuum tumble technology being widely used at home and abroad can shorten the curing time and improve product textural properties.

低温真空滚揉能缩短腌制时间，改善产品质构，目前国内外广泛采用；

Study on the curing reaction kinetics of epoxy electrician molding compound

环氧电工塑料的固化反应动力学研究

The Measuring About Kinetic Parameters of Curing Reaction for HTPB-TDI by Thermokinetics

热动力学方法测定端羟基聚丁二烯固化反应动力学参数

The thermoplastic elastomers from CR/ HPVC blend with excellent mechanical properties were prepared by dynamically curing.

选用氯丁橡胶（CR）和高聚合度聚氯乙烯（HPVC）为主体材料，用动态硫化法制备了一类性能优异的材料&CR/HPVC共混型热塑性弹性体（TPE）。

Phosphorus-doped phenolic resin carbon was prepared by low temperature ( 700 ℃) pyrolysis of thermoplastic phenolic resin containing different amounts of phosphorus pentoxide after curing.

以添加不同含量五氧化二磷的热塑性酚醛树脂为前驱体，经热固化后升温至700℃裂解制备掺磷树脂裂解炭。

Influence of Curing Temperature on Performance of Epoxy Thermosets

固化温度对环氧树脂固化物性能的影响

Chemically induced phase separation is a method for preparing porous polymer. Before curing reaction, solvent or thermoplastic mixes with thermosets and arrives to a homogenous state.

反应诱导相分离法（Chemically induced phase separation）制备多孔聚合物材料，是在固化反应开始之前，溶剂或热塑性塑料与热固性树脂混合均匀后，体系处于均相状态。

A intermediate temperature curing thermosetting oil-surface adhesive was prepared by using the product as curing agent for epoxy.

以此作为环氧树脂的固化剂，配制成中温固化的热固型油面胶。

In order to determine reasonable processing parameters, heating of thermosetting molding compound in the mold and that of heat transfer after curing temperature are analyzed.

本文就模压料在模具中加热过程和达到固化温度以后的传热过程进行定量分析，以确定合理的工艺控制参数。

Thermosetting polyester powder coating and its curing

热固性聚酯粉末涂料及其固化

The Uses of Dielectric Analysis in the study of the Curing Process of Thermosetting Resin

介电分析法在热固性树脂固化研究中的应用

On-Line Measure and Control Thermosetting Resin Curing Processes

热固性树脂固化过程的在线测量和控制

Study on the non-model method of thermosetting resin curing kinetics

热固性树脂固化的非模型反应动力学研究