drawing process的例句大全

Self-tuning Control System for an Optical Fiber Drawing Process

光导纤维拉丝过程自校正控制系统

Study on the drawing process of the UHMW-PE gel fiber

UHMW－PE冻胶丝超拉伸工艺的研究

The numerical simulation results indicate that the variable blank-holder force can improve the formability of box deep drawing process.

研究表明，采用变压边力控制技术可以显著改善矩形盒的成形性能。

How to reduce limit drawing coefficient, cut down procedures, raise efficiency and reduce costs become one of the main research problems for drawing process on the premise of ensuring the quality of products.

如何在保证质量的前提下降低极限拉深系数，减少工序，提高效率和降低成本，成为拉深成形工艺的主要研究问题之一。

Experimentation and Simulation Research of Deep Drawing Process of Metal Sheet with Coating

镀层金属薄板拉深成形的实验与数值模拟

Through the analysis and calculation of the drawing process of the front cover of the brake cylinder, the technological method for drawing the taper part was introduced.

通过对制动缸前盖拉伸成形的工艺分析和计算，介绍了锥形件拉伸的工艺方法，并用数值模拟技术对结果进行分析、预测，模具一次调试成。

In numerical simulation of the drawing process of plate material, in order to get reliable calculation results, the dynamic contact of the plate material with the die need to be simulated accurately.

在对板料拉伸成形过程进行数值模拟时，为获得可信的计算结果，需要准确地模拟出模具与板料之间的动态接触。

The drawing process is the key process of automobile panel forming. And the design of drawing die-face is the main contents of panel stamping process design.

汽车覆盖件拉延工序是覆盖件成形的关键工序，而拉延模具型面的设计是覆盖件拉延工序设计的主要工作。

Simulation of Drawing Process for Circular Metal Sheet and Calculation of Drawing Limit Crack Analysis of Inlaid Circular Metal Cutting Saws

圆筒形件拉深过程的模拟及拉深极限计算镶片圆锯裂纹分析

Experimental study on the effects of material structure during thin sheet drawing process

材料组织性能对薄板拉深工艺影响的试验研究

The increase of draw ratios in three-stage drawing process decrease the linear density of PAN fiber and improve the strength, sonic orientation and tensile modulus.

三级拉伸工艺中各拉伸比的提高均有利于PAN纤维线密度的减小及其强度、声速取向度和抗张模量的提高；

The results showed that in the drawing process, the damage location of the inner membrane interface mainly at the punch fillet area, and the damage location of the outer membrane interface mainly at the die corner area.

研究结果发现在拉深过程中，内层薄膜界面发生损伤的位置主要在凸模圆角区，而与凹模圆角接触过的外层界面都出现了损伤。

This paper proposes a new sheet metal deep drawing process, assisted with the original liquid medium, which replaces the solid granulas to the pressure transmission medium of hydromechanical deep drawing ( liquid or viscous medium).

本文提出了一种采用固体颗粒介质辅助板料拉深成形的新工艺方法。就是采用固体颗粒代替充液拉深中的传压介质（液体或者粘性介质）对板材进行拉深成形。

The breaking strength of PP BCF increased to 1 70 ￣ 1 90 cN/ dtex by appropriately adjusting the amount of chemical degradation masterbatch, increasing spin manifold temperature and optimizing cooling conditions and drawing process.

生产中适当调整降温母粒添加比例，提高纺丝箱体温度，优化冷却条件和拉伸工艺，生产出的丙纶BCF断裂强度可达1.70～1.90cN／dtex。

We test the melt glass viscosity and determine the drawing process parameters.

测试了熔体粘度，得到了拉丝过程仿真的基础数据。

The simulation predictions of temperature field offer some references for the selection of anti-friction material and design of drawing process and die.

对坯料及模具温度场的仿真预测为润滑剂的选取、拉拔工艺及模具设计提供了依据。

Finite Element Analysis and Optimization of the Drawing Process of Head With Thick Semi-Spherical Shell

半球形厚壁封头冲压成形有限元分析及优化

Spinning technology of Australian wool viscose triangle abnormal cross-section polyester blending yarn is separate sliver and blending slivers in drawing process.

澳毛/粘胶/三角形截面异形涤纶20/60/2018.5tex采用分别制条，在并条混和的纺纱工艺流程。

Thickness Variation Research of Drawing Process of Thick-Wall Semi-Spherical Heads

半球形厚壁封头拉深成形壁厚变化规律研究

Numerical Simulation of Variable Blank-holder Force in Box Deep Drawing Process

矩形盒拉深时变压边力的数值模拟