flange的例句大全

Considerations to main engine thrust flange loads in shaft alignment calculation

轴系校中对主机推力轴法兰负荷的几点考虑

Tightness test both the shell and tube sides of the exchanger to check that the flange gaskets are holding tight.

紧力测试对热交换器的管程与壳程，检查法兰垫圈是否紧密。

To reduce the cost and lead time of developing a trimming die, a method to obtain the trimming line in flange process is proposed on the basis of blank grid deformation.

为减少修边模的开发周期和成本，提出一种基于板料网格变形的修边线确定方法。

ⅲ region is tip leakage flow that direction of blade flange clearance turn to suction side;

Ⅲ区为叶片轮缘部中间隙泄漏流动的流动方向转向背面；

ⅳ region is trailing edge vortex region of tip near the flange of blade.

Ⅳ区为叶片出水边靠尾部的轮缘出口尾涡区。

It is suggested that the flanges with 0.25, 0.6 MPa adopt the connection dimension for the flange with 1.0 MPa, while the thickness is kept at the original size, so as to simplify the connection dimension.

建议对0.25、0.6MPa法兰盘采用1.0MPa的对接尺寸，厚度仍采用原来的三种规格，从而实现对接尺寸的简约化。

FEM analysis on loading capacity of square hollow section flange connection

方钢管柔性法兰连接节点性能有限元分析

However, due to the demand for oil and natural gas industry have changed, ANSI flange continuously exposed shortcomings.

但由于石油天然气工业的需求已经发生变化，ANSI法兰的缺陷不断暴露出来。

The material selection of reactor, strength calculation, structure design ( including welding joint and flange seal face) and matters needing attention in equipment manufacture were analyzed and discussed comprehensively by the author.

作者对反应器的选材、强度计算、结构设计（包括焊接接头和法兰密封面）及设备制造中应注意的问题进行了较全面的分析和论述。

3-D Transient Analysis for Flange Sealing System in Reactor Pressure Vessel of Power Station

某电站核容器法兰三维瞬态密封分析

In order to fully used the compression resistance of the concrete, this paper analyzed the stress distribution to the composite beam in the actual use, and put forward to the method calculating the concrete flange plate thickness.

为充分利用混凝土的抗压性能，本文通过分析钢与混凝土组合梁使用阶段的应力分布，提出了一种确定钢梁上混凝土翼板厚度的方法。

Design of progressive die for fixing cover with flange seal

带凸缘密封固定盖级进模设计

Rather than plastic, the it is sculpted from butt to flange into a ported aluminium bullet.

而不是塑料，它是从屁股雕刻成移植铝子弹法兰。

The 8 node solid element with an one point quadrature is used for the model of grinding wheel, flange, spindle and bearing.

砂轮、法兰、主轴及支座采用一点积分的8节点实体单元。

There is no unified explanation and exact conclusion on connecting state between short conical flange type C-form spindle end and face plate.

关于短锥法兰式C型主轴端部与花盘等机床附件的联接定位问题，目前尚未有统一的解释和确切的结论。

Stress concentration often happened along the junction of some axial-flow hydraulic turbine blade and flange of pivot. The spindle blade of a spinning machine is characterized by high rotation speed and good wearability at ire pivot end.

轴流式水轮机转轮叶片进出口边与枢轴法兰连接的根部易出现应力集中。锭杆是纺机中一种数量大、转速高、尖端要求耐磨的杆状零件。

The Welding Procedure for Large Diameter Flange of Spiral Plate Heat Exchanger

螺旋板式换热器大直径法兰的拼焊工艺

The spiral winding gasket flange angle increased while the MMC gasket flange angle deceased, indicating that MMC gasket inner and outside ring limited the rotation of flange.

缠绕垫法兰受外载后转角增大，而MMC垫片的转角减小，说明MMC垫片的内外环起到了限制法兰转动的作用。

Place chisel or spacer under the halfshaft flange.

将凿子或厚垫片放在半轴法兰下面。

Gasket is a major element which connects the pipe and flange.

密封件作为管道和设备法兰连接的主要元件，对密封起重要作用。