flanges的例句大全

Flanges threaded for smaller pipe sizes, or flanges adapted for welding, are also available.

带螺纹的法兰也适用于较小管子的尺寸，或适宜焊接法兰。

Hubbed threaded cast iron pipe flanges

GB/T17241.3-1998带颈螺纹铸铁管法兰

Tubes and pipes of the foregoing cross-sections may be polished, coated, bent, threaded, drilled, waisted, expanded, cone-shaped or fitted with flanges, collars or rings.

上述截面的管子可经抛光、涂层、弯曲、攻丝、钻孔、缩腰、胀口、成锥形或装法兰、颈圈或套环。

It is suggested that the flanges with 0.25, 0.6 MPa adopt the connection dimension for the flange with 1.0 MPa, while the thickness is kept at the original size, so as to simplify the connection dimension.

建议对0.25、0.6MPa法兰盘采用1.0MPa的对接尺寸，厚度仍采用原来的三种规格，从而实现对接尺寸的简约化。

Design of Nonstandard Flanges for Resin Reaction Vessel

树脂反应罐中非标准法兰的设计

This thesis describes the field erection process of the loop reactor and the assembly welding method of a pair of the axial-flow pump flanges.

文章着重描述了环管反应器组装过程以及轴流泵弯头配对法兰的组焊方法。

Numerical Sealing Analysis for Sealing System in Reactor Pressure Vessel Flanges

核容器法兰密封系统密封性能数值分析

Beginning with the standard reverse reduction gear with parallel axes and input and output flanges on different ends, it is shown how the other versions can be derived from this standard version.

首先是标准的平行轴线带倒车减速器和各种形式的输入、输出法兰，可看出其它结构均可从该标准结构中衍生出。

Principle and method of length modification for cylindrical portion of the welding neck flanges ( hub thickness at small end) are explained in this paper in order to ensure the flange strength and stiffness, if the cylindrical portion thickness is not equal to the butted shell thickness.

本文阐述了长颈对焊法兰直边段厚度与对接圆筒厚度不等时，为确保法兰强度采取的调整法兰直边段高度的原理与方法。

The Stress Analysis of Hubbed Socket Welding Flanges with Neck

带颈承插焊法兰应力分析

Up till now, there is still no relatively complete computation method for the hubbed socket welding flanges with neck.

对于带颈承插焊法兰目前还没有一套较完整的计算方法。

One-side welded bed plate for flanges in marine

GB/T11693-1994船用法兰焊接单面座板

The web and flanges of the main girders were fabricated from ASTM A441 steel.

主梁的腹板和翼缘用ASTM A441钢制造

The friction behaviors in the flanges area and die corner radius area during the variable forming speed/ forming loading stamping process are studied by flat plate friction test and stretch bending friction test.

为此，针对拉深成形，分别采用平板滑动摩擦实验和拉弯摩擦实验，研究了变速/变载条件下板料在法兰处和凹模圆角处的摩擦行为。

In exceptional cases the use of slip-on flanges may be considered.

特殊情况下，可考虑搭接法兰。

Copper alloy hubbed slip-on flanges for brazing or welding

GB/T15530.4-1995铜合金带颈平焊法兰

Wafer-style held in place between two pipe flanges. Easy to install but cannot be used as isolation valve.

平板式（对夹式）：固定在两个管道法兰之间。安装容易，但是不能作为隔断阀使用。

Add sealed shim between the two flanges and then lock down the bolt. tighten up

安装时两法兰间需加密封垫片，然后均匀拧紧螺栓。密封，拉紧，拧紧

Trial-design on new-type composite box arch bridge with steel truss webs and concrete flanges

钢腹杆-混凝土新型组合箱拱桥试设计

The web and flanges of the main girders were fabricated from ASTM A 441 steel.

主梁的腹板和翼缘用ASTMA441钢制造.