forming pressure的例句大全

The significant of influence to each performance of compact is in sequence of forming temperature forming pressure holding time.

方差分析结果表明，对压坯各性能影响的显著性大小排序为：成形温度成形压力保温时间。

The control object is the optimum forming temperature and it is realized by controlling forming pressure.

优化目标为最佳成形温度,而温度的控制主要通过压力控制来实现.

The relationships between thermo physical properties and porosity, forming pressure and space-holder addition were investigated.

总结得到了热物性参数与孔隙率以及制备这些毛细芯所使用的成型压力和造孔剂添加量之间的关系.

Influence on Behaviour of Alumina Ball by Using Different Forming Pressure

成型压力对氧化铝瓷球性能的影响

Engineering Calculation of Forming Pressure on Cross Wedge Rolling for the Blank of Slip Joint Pliers

鲤鱼钳毛坯楔横轧成形压力的工程计算

the influence of powder grain size and forming pressure are discussed for the performance of w-cu composites.

研究了粉末粒度、成型压力及铜的损耗对钨铜复合材料制备的影响。

calculation of force-energy parameters of forming pressure on cross wedge rolling for the blank of cutting pliers etc

钢丝钳毛坯楔横轧成形压力的力能参数计算

The influence of powder size and forming pressure are discussed for the performance of W-Cu composites.

着重研究了粉末粒度与成型压力对钨铜材料烧结致密度的影响.

The local valley wind and the group of the thermal series islands, and thermal and dynamical circulation of the low pressure under the background of the weak pressure and average pressure fields were the major causes of forming the transportation convergence.

弱气压场或均压场背景下地方性山风及山前串状城市热岛群形成的热力性、动力性低压环流，是输送汇形成的主要原因。

Restore the plug inside the unit by sliding the plug button while pressing it. Control on blank holder pressure ( BHP) during viscous pressure forming ( VPF) thin-walled sheet metal parts

边按压边向机内侧滑动，使插头按钮收藏在机内。薄板件粘性介质压力成形过程的压边力控制

The effect of the multi-scale structure forming process by shot penning process parameters including shot peening pressure, duration time, diameter of projectiles and so on were discussed.

通过调节不同的喷丸工艺参数，探讨弹丸直径、喷丸时间、压力等，对表面形成多尺度复合结构的影响。

This experimental system is helpful to find out the process design experience and to test loading feasibility for tee tube hydroforming and it will make a positive contribution to exploring the forming mechanism of internal high pressure hydroforming.

该试验系统的建立，为摸索T形管复合胀形工艺设计经验、验证T形管复合胀形加载方案的合理性以及深入分析内高压胀形的成形机理提供了实践平台。

The effects of blank holder pressure and lubricated condition against friction on the stamping forming were dis ˉ cussed as well.

在合理工艺的基础上讨论了压边力和摩擦润滑条件对冲压成形的影响。

Under the given experimental condition, the hydroforming process of automobile lower arm is experimentally studied where the influences of main process parameters are considered, such as the internal hydraulic pressure, the axial feeding, and the tool geometry on the forming performance.

在给定实验条件下，分别考察和研究了液压胀形的主要工艺参数（如管内压力、轴向进给量及摩擦条件）对成形过程的影响。

In this the thesis, the characteristics of the magnetic field in electromagnetic forming with flat spiral coil are discussed field. ANSYS software is used to simulate the magnetic field and magnetic pressure in it.

本文讨论了平板线圈电磁成形的磁场特性，利用ANSYS有限元分析软件对平板线圈电磁成形的磁场进行了模拟。

The Numerical Control Hot Spinning Process of Forming High Pressure Cylinder

高压贮气瓶数控加工热旋压成形工艺

A study on forming limit of thick cylinder under axial pressure with support of mandrel

厚壁管有芯镦锻成形极限的研究

The results show that endwall fence can control secondary flow by decreasing the influx of pressure side of horse vortex into passage vortex and forming reversed fence vortex.

结果表明，端壁翼刀主要通过阻断马蹄涡压力面分支汇入通道涡和有效产生反向翼刀涡来控制二次流。

In the process of HDD, cavity pressure control accuracy is a key factor for improving sheet forming limit.

在拉深工艺过程中，液室压力系统的控制精度对板料成形的质量有着至关重要的作用，是提高板料成形极限的重要因素。

Non-die Explosive Forming of Conjugated Spherical Pressure Vessels

相接球形压力容器无模爆炸成形技术