front suspension的例句大全

Vibration Analysis, Simulation and Optimization of Wishbone Type Independent Front Suspension

基于虚拟样机技术的双横臂独立前悬架振动仿真分析及参数优化

In conclusion, we know after the front suspension optimized, the front wheel alignment parameters is more reasonable. The variation of tread is minished so that the abrasion of the tire is reduced. And also the vehcile keep some understeering characteristic after front suspension optimized.

最后总结出优化之后的前悬架使得前轮的定位参数更加合理，减小了轮距变化量，从而降低了轮胎磨损，并保证了样车具有一定的不足转向特性。

Experimental model analysis of front suspension system for automobile is introduced in this paper.

本文介绍了对某轻型客车前悬架系统的实验模态分析方法.

This article is a bench test and road test study on a mini car front suspension shock absorber in the condition of the low temperature noise, which comes up in winter in the north-east area of China.

该文介绍对某微型车前悬架减振器在东北地区冬季出现的低温噪声进行的台架试验和道路试验研究，并据此提出了该悬架减振器低温噪声来源和控制的初步结论。

DaimlerChrysler AG spokesman Max Gates said the front suspension lower ball joint could experience excessive wear and looseness, leading the ball joint to separate.

戴-克公司发言人马克斯·盖茨表示，被召回汽车存在的主要问题是前悬架球窝接头处有可能过度磨损并松开。

Front Suspension Design of New Three Wheels Sport Car and Vehicle Handling Stability Analysis

新型三轮跑车前悬架设计及整车操纵稳定性分析

front suspension: double-joint strut, coil springs, gas-filled dampers, anti-roll bar.

前悬架：双联合支柱，线圈弹簧，充气减震器，防侧倾杆。

to study roll characteristic of a vehicle's front suspension, an analytical simulation model of a vehicles front suspension is established based on adams in which anti-roll bar had been modeled by three methods.

在悬架侧倾特性分析中建立了基于ADAMS软件平台的某车辆前悬架仿真分析模型，其中横向稳定杆结构分别采用三种不同方法进行建模。

based on adams/ hydraulic and adams/ autoflex module, the hydraulic and front suspension, the leaf-spring sub-systems, are established and coupled to the whole system;

运用ADAMS／Hydraulic（液压模块）建立了液压子系统并与全炮模型耦合；

Using ADAMS/ Car model, by front suspension steering system of the mini car, discuss kinematic and compliant character, establish the foundation for research of handle stability and ride for full vehicle.

针对某微型车的前悬架转向系统，利用ADAMS／Car模块进行双轮反向跳动和转向的耦合试验，分析了运动特性和弹性运动特性参数，为整车的操纵稳定性和平顺性的进一步研究奠定了基础。

Applying the vehicle-system-oriented numerical virtual prototype technology, the multi-body dynamic models of front suspension, rear suspension, tire, the steering system and a complete vehicle are created with ADAMS software.

运用面向整车系统的数字化虚拟样机技术和大型机械系统动力学仿真软件ADAMS建立了包括前后悬架、轮胎、转向系统及整车的多体动力学模型。

For the height control part, two air springs of front suspension are controlled separately and two rear suspension are controlled together. For each single controller the gas charge and exhaust processes are considered too.

对于车高控制部分，对前悬两个空气弹簧独立控制，后悬两个空气弹簧一同控制，并对每组控制器分充放气过程进行控制。

Front Suspension: Independent double-wishbone with dual single-rate springs provide 10.5 inches of travel.

前悬架: 独立双叉双单率温泉一十零点五英寸旅行.

Expound the application of ADAMS/ CAR in front and rear suspension development respectively.

分别阐述了ADAMS/CAR在前悬架和后悬架设计开发中的应用。

Precise and responsive handling is generated by fully independent front and rear suspension.

精确和响应处理是完全独立的产生前，后悬挂。

Kinematic model for a car's front multi-link sus-pension and steering system was developed using ADAMS/ CAR module. An investigation was done of the suspension's kingpin axis and wheel orientation.

应用ADAMS软件的CAR模块建立了轿车多连杆式前悬架和转向系统的多体运动学模型，对主销和前轮定位角进行了仿真计算研究。

The Design and Application of A Kind of Front Wheel Suspension for Motor

一种机动车前轮悬架的设计及应用

Through KASS analysis calculation, acquire the transformation rule of front wheel location parameter and steering error of McPherson suspension and steering system.

通过KASS程序分析计算，得出麦弗逊悬架和转向系统的前轮定位参数及转向误差的变换规律。

Macpherson Suspension Design Optimization and Influence on Automobile Front Wheel Shimmy

麦弗逊悬架优化设计及其对摆振的影响

abarth has also fitted a larger anti-roll bar together with front springs that are20% harder than those of a standard suspension system.

阿巴特还装有一个更大的防侧倾杆与弹簧的前20%的困难是比一个标准的悬挂系统。