gear pin的例句大全

In a cycloidal reducer, pin wheels are composed by precision components such as the pin wheel housing, a gear pin and outer casing.

在摆线针轮减速机中，针轮是由针齿壳、针齿销、套3种精密零件组成；

coefficient of gear pin diameter

针径系数

gear pin diameter and effective facewidth

针齿直径和有效齿宽

The Parameterized Design for the Sheave Device with the Single-pin and the External Gear

单圆销外啮合槽轮机构的计算机参数化辅助设计

The two force analysis calculation results are consistent in the pin gear force, the touch pin gear at the same time and the touch stress value distribution, and the biggest error of touch stress between them is less than 5 percent. 3.

两种受力分析计算结果在针齿的受力、同时接触针齿、接触应力的数值分布上均呈现了一致性，且两者最大接触应力的误差在5%左右。

The Selection of the Number Over Teeth and Pin Diameter on the Great Addendum Modification Gear

大变位齿轮跨齿数及量柱直径的选取

It is one of the difficulties in the die-casting design for the design of the lateral core-pulling with long distance core-pulling and great closed forces, so the secondary core-pulling mechanism with angle pin, rack and gear has been used to solve the problems.

抽芯距离长、包紧力大的侧向抽芯机构是压铸模设计的难点之一，采用斜销-齿条-齿轮二次抽芯机构解决了这一问题。

belaying pin: a short, removable wooden or metal pin fitted in a hole in the rail of a boat and used for securing running gear.

系索栓：可插入船栏的洞内以固定船只的一种短的，可移动的木拴或金属栓。

A new method is proposed for analysing the meshing force exerted between the pin teeth and the cycloidal gear teeth in the course of the cycloidal pin gear epicyclic transmission.

提出了一种分析摆线针轮行星传动中针齿与摆线轮齿间啮合力的新方法。

Study on Generating Pinholes of Pin Gear Housing Using Circular Tooth Slotter

用圆弧齿插刀展成针轮销孔的几个技术问题

Pinhole machining of pin gear housing is one of important procedures in manufacturing cycloid speed reducer.

针齿壳销孔的加工是摆线针轮减速器制造的重要步骤之一.

Extrusion System: frequency variable motor, cycloidal pin gear speed reducer and high qualitynitrifiedfeed cylinder screw.

挤出系统: 变频调速电机 、 摆线针轮减速箱加优质氮化料筒罗杆.

Insertremove gear safety pin.

请插上取下起落架安全销.

This paper discusses computing backlash of the gear pair and output mechanism of shaft of pin kind according to the requirement of tolerance of designing and manufacturing and the probable maximum and minimum values of backlash are precomputed, using probabilistic method.

文中叙述齿轮副的回差计算和销轴输出机构的回差计算，是根据设计制造的公差要求，按概率统计的方法预算出可能出现的最大与最小的回差值。

By using of the finite element method, this paper has analyzed the bending stress of the circular arc toothed gear used in fewer teeth difference transmission composed of circular arc toothed gear and pin gear, and verified the result with electrometry test.

利用有限元法，对圆弧针齿少齿差传动机构中的行星轮&圆弧齿轮的弯曲应力分布作了分析，并用电测实验进行了验证。

The normal lines of the cam pitch curve at the meshing points intersect at the instantaneous center of the cam and the pin gear, which accords with the meshing principle of tooth contour.

在凸轮与针轮啮合的瞬时，各针齿与凸轮啮合点处，凸轮理论廓线的法线交汇于该瞬时凸轮与针轮的速度瞬心，符合齿形啮合基本定理。