gear teeth的例句大全

The gear disk of high speed and movable teeth are welded through special welding, it makes the teeth is durable, safety and reliable.

高速齿盘与活动牙齿经特种焊接，使活动牙齿坚固耐用安全可靠。

By using of the finite element method, this paper has analyzed the bending stress of the circular arc toothed gear used in fewer teeth difference transmission composed of circular arc toothed gear and pin gear, and verified the result with electrometry test.

利用有限元法，对圆弧针齿少齿差传动机构中的行星轮&圆弧齿轮的弯曲应力分布作了分析，并用电测实验进行了验证。

Inquiring Into the Balance of Gear Mechanism With Small Teeth Difference

少齿差偏摆齿轮传动机构平衡的探讨

The paper study the phenomenon of server teeth put into gear, analyse the phenomenon how effect the few differences of teeth motor.

研究了少齿差传动中的多齿啮合现象，分析了其对各轮齿负荷的影响以及这些现象对少齿差马达的结构影响，并在设计的过程中加以体现。

Establishing spiral gear's optimized model, optimizing the number of teeth, the module, helix angle and facewidth to make the volume of spiral gear smaller.

建立弧齿锥齿轮的优化模型，对齿轮的齿数、模数、螺旋角和齿宽进行参数优化，实现弧齿锥齿轮副体积较小；

Formation spiral bevel gear has straight tooth profile and more teeth, and tooth grinding efficiency is low.

由于成形法螺旋锥齿轮的大轮具有直齿廓且齿数多，磨齿加工的效率低，因此，考虑对其采用高速切削加工的方法。

The reverse gear adopts the design of short teeth, which can decrease the lock probability, and reverse restrictive is adopted to avoid shift reverse when reverse shift from5th position.

倒档齿轮采用短齿设计，有效降低锁止比，同时采用倒档锁机构，避免了摘五档误入倒档，提高安全性。

Research on Motion Parameters of Slide Pair of End Face Harmonic Gear Drive of Oscillating Teeth

活齿端面谐波齿轮移动副的运动参数

The construction forms of sliding-teeth gear pump ON SLIDING STRUCTURES

活齿泵的结构形式略论滑动构造

Common Profile Equation of the Annulus in Sliding& Teeth. Gear Pair and Its Analysis of Clearance

活齿齿轮副内齿轮齿形通用方程式及间隙分析

Grinding Device and machined Error Analysis of Gear for Wavy Teeth Driving

波齿传动中内齿轮齿形磨削装置及加工误差分析

This paper analyses error of gnashing teeth in the course of inside gear producing, and puts forward the eliminating methods.

通过对齿轮加工过程中造成切齿误差的分析，提出了相应的消除方法。

Research on Flow Characteristics of the Moveable Teeth Gear Pump

活齿无啮合力齿轮泵的流量特性研究

And the value of the friction coefficient is very small, its order of magnitude only being 10-3. So, it is reasonable that the friction force on teeth surfaces are ignored when the gear-driven contact fatigue strength is designed.

节点啮合处的齿面摩擦系数很小，其数量级为10一，，因此在做齿轮强度设计时，忽略齿面摩擦力的影响是有理论根据的。

Carries through the meshing experiment of many pairs of teeth and the pre-alarm experiment of tooth-face crack damage with the crown gear coupling by use of the special experiment rig of the crown gear coupling designed selves.

利用自行设计的鼓形齿联轴器专用台架实验装置，进行了鼓形齿联轴器多齿啮合实验和齿面裂纹破坏预警实验。

Bevel gear: Either of a pair of gears with teeth surfaces cut so that they can connect unparallel gear shafts.

正齿轮和斜齿轮滚齿机斜齿轮：用以连接不平行齿轮轴齿轮的任一对齿面切削。

Repair to Broken Teeth of Reducer Large Gear Used in WK-4 Excavator

WKz&4型挖掘机中减速机大齿轮断齿的修复

Analysis of Teeth Surface Damage and Fracture for a Tail-decelerated Gear

某尾减齿轮齿面损伤与断齿分析

Research and Design of ORT Reduction Gear Based on Movable Teeth Transmission

基于活齿传动的ORT减速器理论研究与设计

A novel reducer was designed in the Pro/ E by using the convert-tooth shape method to calculate the involute small teeth designed on the profile of the epicycloidal gear and hypocycloidal gear.

采用折算齿形法利用Pro/E设计了一套叠加渐开线小齿的减速器三维实体模型，分别计算了内外摆线轮的渐开线轮齿。