gear tooth的例句大全

Chamfering Process of Gear Tooth Profile

齿轮倒棱工艺

Method for eliminating 3-shaped contact zone on gear tooth profile

齿轮之字形接触区的消除方法

Through the Sliding Ratio to reflect the points of the gear tooth surface in gear meshing process. 2.

通过该系数来反映齿轮在啮合过程中齿面各点的接触情况。

Chamfering Process of Gear Tooth Profile Calculation and Drawing of Involute Part in Gear Profile Sample

齿轮倒棱工艺渐开线齿形样本中渐开线部分的计算与绘制

contact stress analysis of a spur gear tooth by using boundary elemental method

应用边界元方法的正齿轮接触应力分析

The Fracture Process Simulation and Fracture Strength of Gear Tooth in Mining Machine

采掘机械齿轮轮齿断裂过程仿真与断裂强度

Its basic gear tooth profile is double circular arc spiral bevel gear tooth profile.

双圆弧弧齿锥齿轮采用等高齿，在轮齿任意法截面内具有完全相同的齿形，由于采用平面齿轮原理加工，能形成点接触共轭齿面，符合齿廓啮合的基本定律。

Sliding ratio is an important index which can evaluate the wear of spherical gear tooth surface.

采用滑动系数作为衡量球齿轮齿面滑动磨损程度的重要指标。

Study on modification technique of hourglass worm gear tooth surface

小柱面包络环面蜗杆齿面修形方法研究

The Computer Simulation Technology of the Hourglass Worm Gear Tooth Meshing Line

环面蜗杆齿面啮合线的计算机仿真技术

The Comparative Study of the Bending Stress and Elastic Deformation Calculation of Gear tooth

齿根应力与轮齿弹性变形的计算方法进展与比较研究

Gear tooth tip relief based on standard hob

基于标准齿轮滚刀的齿顶修缘

When designing gear hob, worm gear hob and shaping milling cutter, it should be verified whether the interfere would occur between grinding wheel and the next gear tooth on condition of pledging the relief grinding length of the back of tooth.

在设计齿轮滚刀、蜗轮滚刀和成形铣刀时，要校验在保证齿背铲磨长度的情况下，所用砂轮是否和下一个齿发生干涉。

Study of Virtual Simulation of Grinding of Digital Gear Tooth Surface

数字化齿面磨削加工虚拟仿真研究

Calculation of Pressure Angle and Spiral Angle on Spiral Bevel Gear Tooth Surface

螺旋伞齿轮齿面上指定点处压力角及螺旋角的计算

Ausform finishing process for hardened gears and study on gear tooth deformation theory

硬齿面齿轮精密热滚挤工艺及轮齿变形的研究

A Calculation of Bulk Temperature and Thermal Deflection of Gear Tooth about Profile Modification

齿轮本体温度场和热变形修形计算

Firstly, the data of the surface ′ s point of a tooth are gotten from the spiral bevel gear tooth surface equation, then, the whole tooth surface data are formed through converting the previous data.

首先，根据弧齿锥齿轮的齿面方程求出一个轮齿的齿面上点的数据，然后经过旋转变换便形成全部齿面的数据。

A Proof of Thinned Addendum Thickness of a Gear Tooth Generated with Positive Correction

正变位齿轮齿顶厚度必变小的证明

The differential structure of extended epicycloid bevel gear tooth surface is analyzed when formatted on free-form bevel gear milling machines.

分析了Free form型铣齿机上用成形法加工延伸外摆线锥齿轮时的齿面微分几何结构。