given load的例句大全

At last, the main steam pressure during optimum sliding pressure operation of the unit at a given load is determined, and the theoretically calculated and the tested main steam pressures during optimum sliding pressure operation are basically the same.

最后，确定了机组在给定负荷下最佳滑压运行的主蒸汽压力，理论计算和试验结果表明，最佳滑压运行主蒸汽压力基本相同。

after softening with se-3, various sensuous indexes of leather sample, such as tensile strength, given load extensibility, breaking extensibility and water permeability are obviously superior to the original ones.

将SE-3用于皮革柔软处理，经处理后革样的各种感观指标如抗张强度、规定负荷伸长率、断裂伸长率、透水性明显优于原革样。

The variations of terminal voltage and stator frequency with the load impedance and the load current are given out.

给出了异步发电机的端电压和定子频率随负载变化的曲线以及外特性曲线。

The method of calculating buckling critical load of open section thin-walled bar as the type of curly cross section strip is given. 3.

给出了弯曲截面钢带这种开口薄壁类型杆件的失稳临界力的计算方法。

Taking the error occurring in no-load test of three phase AC traction motor in our company as example, analyzing with symmetrical components method, the main cause of error-three phase non-symmetry and corresponding solutions were given in this paper.

根据本公司轨道交通用三相异步电动机在空载试验时所出现的误差，用对称分量法进行分析，找出电源的三相不对称是三相异步电动机空载试验时产生误差的主要原因，并给出了相应对策。

And simulated three-point bending test of concrete, given the failure process of the specimens map and the load-displacement curve.

模拟了混凝土的三点弯曲试验，给出试件的破坏过程和荷载&位移曲线。

By considering the compressibility of lubricant and the transient effect of variable load, sliding Velocities and curvature varying with time and coordinate, the transient elasto-hydrodynamic lubrication analysis on spur involute gears is given.

本文综合考虑润滑流体的可压缩性、齿轮传动重合度对轮齿载荷的影响以及滑动速度、曲率半径随时间和座标变化的瞬态效应，对渐开线直齿圆柱齿轮传动进行瞬态弹流完全数值分析；

The maximum steam load produced by the bark was determined by the bark fixed combustion temperature and the capacity of attemperator system when the basic steam load was given.

在一定的基本蒸汽负荷下，燃树皮产汽负荷的上限值可根据流化床中树皮的稳定燃烧温度和减温系统的工作能力来确定。

The calculation method of flight safety time margin is given when critical parameter respectively is load and height.

给出了临界参数分别为过载和高度时，飞行安全时间裕度的计算方法。

It is given a novel electronic simulative load and proved that the IGBT can simulate the real time waveform of the current and voltage in welding.

提出了一种新型的电子模拟负载，并通过理论分析和大量的实验研究证明了采用这种电子模拟负载模拟动态电弧的实时变化是可行的。

During the research work, a formula of load identification has been acquired by applying the precise time-integration method; furthermore, the matrix expression has also been given.

基于此，文章引入精细时程积分的理论，并将其应用到载荷识别的逆问题中，进而给出了基于模态分解形式的载荷识别公式，并且构造出了有利于计算机编程实现的矩阵表达形式。

The shape optimization design of arch dam is using mathematics plan method to look for the most rational bodily form under the given topography, geology and load.

拱坝体形优化就是在给定的地形、地质以及荷载条件下，利用数学规划方法，寻找最合理的体形。

At the same time, a detailed analysis about some fundamental concepts, which often appear in the development of ARM embedded software, such as memory map and scatter-loading file, is also given in this paper.

同时对在ARM嵌入式软件开发过程中经常遇到一些基本概念，比如存储器映射、分散加载文件等进行了详细的解释。

Figures all-embracing moment of lining structure on different water pressure are given, taking pressure of suddenly effluent water as move load act on lining by applying the theory of structure mechanics moment influence line.

运用结构力学的弯矩影响线理论，把突水压力作为衬砌结构上的移动荷载，给出不同突水压力下衬砌结构的弯矩包络图。

When the system load is lower, the policy guarantees that the call blocking rate of higher-priority traffic is below its given threshold and at the same time, decreases the call blocking rate of lower-priority traffic.

当系统负荷较低时，该策略在保证较高优先业务的阻塞率维持在门限值的同时，减少了较低优先业务的阻塞率；

Implementation of three-tier distributed system based on CORBA and load-balancing technology is given at last.

最后，结合我开发的三层应用系统&青海石油物资管理系统，详细讨论了CORBA服务器和客户端的实现过程以及负载平衡技术在产品中的实现。

The assemble type and load of the spindle bearing is analyzed, and the practical example is taken to explain in detail applied preload and its measurement and calculation, the exercisable exact data is given.

对磨床主轴的轴承装配形式及受力状况进行了分析，并用实例对预载荷的施加及测量计算加以详解，给出明确的可操作数据。

The stress and deformation under elastic-plastic behavior are given for the structure of combined thick cylinder, and the simple deformation on the influence of structural plastic limit load is discussed.

给出了组合厚壁圆筒结构在弹塑性状态下的应力及变形情况，并且论述了筒体变形对结构塑性极限荷载的影响。

The distributions of stress in different position of each belt were given out, when inflation pressure, vertical load and steady rolling were applied to the tire.

分析了轮胎在充气压力、垂直载荷以及稳态滚动下各带束层中的应力分布情况。

From experimental readings, the dynamic changing regularity of water wall parameters and the response curve are confirmed under the disturbance of outlet pressure, heat load, inlet mass flow speed and inlet temperature. Sone theoretical analyses are given.

在出口压力、热负荷、进口质量流速和进口温度参数扰动下，确定水冷壁参数动态变化规律和响应曲线，并进行了理论分析。