gluing的例句大全

Study on Method of Confirming the Leading Factors of API Pipe Thread Gluing

API管螺纹粘扣主要因素的确定方法研究

Tubing Thread Gluing Failure: Analysis& Countermeasures

油管粘扣失效的分析与对策

: Thread gluing is a common failure of oil tubing found during manufacture and operation.

石油油管的粘扣是油管生产和使用过程中常见的一种失效形式。

Influence of using hydraulic tongs on thread gluing of tubing

使用液压钳对油管粘扣的影响分析

Improving the Quality of Petroleum Casing Pipe Application to the Worksites by Reducing the Thread Gluing

改善粘扣现象提高石油套管现场使用质量

It is a precondition and base of improving anti-galling performance of oil well pipe to make sure the leading influencing factor of API pipe thread gluing.

科学地确定出油井管螺纹粘扣的主要影响因素是提高油井管抗粘扣性能的前提和基础。

For being convenient to change the outside material face layer, the wrapping outside material can be provided with a zipper or a thread gluing device.

为方便外材面层的更换，所述包裹的外材上可以带拉链或粘扣装置。

The reasons caused seal and slippage failure are complicated, the most important factor was the thread gluing reduced the intensity and the sealing property of the thread joint.

造成密封和滑脱失效的原因较为复杂，最重要的因素是螺纹粘扣降低了螺纹联接的强度和密封性能。

Thread gluing is one of the main failure forms for oil tubing and casing connections, and it directly deteriorates the sealing performance and the connecting strength of oil tubings and casings.

粘扣是油套管接头的主要失效形式之一，直接影响油套管的密封性能和连接强度。

Drilling operation in this well was faced with many big challenges, mainly including low ROP, thread gluing of drill collar, drilling tool breaking, large formation dip, enlargement of well deviation, as well as difficult well trajectory control.

该井施工难度大，主要表现在机械钻速缓慢、易出现钻铤粘扣、断钻具，地层倾角大井斜上升问题突出，井身轨迹控制困难。

The results showed that the major cause of thread gluing is over plastic deformation of partial thread face, and that the distribution of contact stress can be improved with the taper mutation, which has proved to be effective in the factory manufacturing.

认为产生粘扣的主要原因是螺纹齿面局部过量的塑性变形，通过变锥度的方式能使接触应力分布规律得到改善，并在现场生产中得到验证。

The distribution of the stress in casing connection, the value of make-up torque and thread off load are studied when the casing connection is assembled or loaded with internal pressure and axial tension, which are very important for gluing, leakage and thread off failure analysis.

套管接头在装配、内压和拉伸载荷工况条件作用下，沿接头的应力分布规律、上扣扭矩和滑脱力的大小，对分析套管接头粘扣、泄漏和滑脱的失效有重要参考价值。

The design and application of control system for carton gluing machine

全自动纸箱粘合机控制系统设计与实现

It uses of heat glue to save the gluing time and meet the environmental needs.

该机采用热熔胶，可节省上白胶，黄胶过烤箱之时间，并且符合环保要求。

EVA, foam gluing and laminating with fabric or artificial leather.

本机可广泛适用于泡棉、布类、塑胶皮、EVA、皮革等上糊贴合。

The machine consists of a gluing unit, auto mastic laminating unit and counter ejector unit.

该机器由上胶单元，裱纸单元及计数排出单元组成。

The lifting oil cylinder can not work normally due to the wear of support guide ring or gluing off release at the connecting position between the support guide ring and the inside wall of cylinder after the lifting oil cylinder used for a period of time.

在举升油缸使用一定时间后，其支承导向圈磨损或支承导向圈与缸简内壁的联接处出现脱胶剥离，致使举升油缸不能正常工作。

Formation process of bonding strength during wood gluing operation

木材胶接时胶合强度的形成过程

In his tiny kitchen, he taught the kids to make miniature kites by heating sticks of bamboo over a candle until they were pliable, then gluing on sheets of rice paper.

在大师狭窄的厨房里，他教了孩子们制作微型风筝：将竹棍置于烛火上烤，直到它变得柔韧易弯，然后糊上一张宣纸。

The gluing mechanism of API round thread casing and tubing is analyzed.

分析了API圆螺纹油套管发生粘扣的基本过程及机理.