groove的例句大全

At present, the finger-like grinding wheel is widely used to approximately grind elliptical groove in many manufacturers of CVJ, but the theoretical error of this method is large.

目前，生产厂家大多采用指状砂轮近似磨削椭圆沟道，理论误差较大。

Based on the theory of up-curl chip breaking limits, we get the theoretic predictive formula of chip's curling radius of two-dimensional groove chips which can be defined by nine parameters and the theoretic predictive formula of Critical feed-rate;

本文从上向弯曲切屑折断界限理论出发，推导出刀片九个参数二维槽型切屑流出圆半径及极限进给量的理论预报公式；

In order to carry out local autonomous teleteaching in remote welding, this paper develops the groove touch force models for welding groove start and end sections, welding groove section, and welding teleteaching section.

在遥控焊接遥示教过程中，为实现遥控焊接微观局部自主示教，建立了遥控焊接坡口起焊段、收弧段、焊接坡口和焊接坡口示教过程的接触力力学模型。

Through a series of different flow velocities of bearing temperature contrast found that open slot bearing cooling effect is superior to that in the vicinity of groove bearing.

通过一系列不同流速下轴承温度的对比发现，全开槽轴承冷却效果明显优于半开槽轴承。

The special feature of the new testing method is that a cake-like sand test piece with V-shape groove on its surface is heated from bottom to top in a new-designed high temperature shock heating furnace.

新试验方法的特点是采用表面有V形沟槽的圆饼形型砂试件，在激热试验炉中受到自下而上的高温烘烤。

For a groove welded tension member in3/ 4 in. plate, what is the maximum size of fusion discontinuity permitted in astatically loaded member?

对于3/4英寸板材的受拉构件坡口焊缝，在承受静载荷时，熔合性缺陷允许的最大尺寸是多少？

The groove digging mechanism is connected with the loading vehicle through the tension rod and the distance rod.

挖槽机构通过拉力杆、推力杆与载车相连。

The main construction processes of the tensioning system include the location and fixation of steel spiral rope, and the installation of anchorage groove, anchorage device and tensioning equipment. Its construction techniques are strict.

其张拉系统的施工主要包括钢绞线的就位、固定，锚具槽、锚具及张拉设备的安装，张拉等步骤，施工工艺严谨。

There is a located groove on the flanging concave die, which solves the interferential problem with piercing terrace die, it uses nitrogen cylinder to adjust the pressure on material, as the results, the die structure is simplified, and the productive efficiency gets improved.

翻边凹模设有让位槽，解决了其与冲孔凸模干涉的问题；使用了氮气缸来调节压料力，简化了模具结构，提高了生产效率。

In this paper, shearing test on 72 cube specimens ( 150mm × 150mm × 150mm) with cutting groove bonding has been carried out, using the self-made shearing equipment.

采用自制的剪切夹具对72块150mm×150mm×150mm沟槽式新老混凝土粘结试件进行了抗剪试验。

A report of the bulk rice storage test on the land groove air DUT of grain parcels stacking

谷包堆码地上槽通风道散装稻谷储藏试验报告

Sideway Fine Feed System for Finishing Piston Ring Groove

精切活塞环槽侧向微进给系统设计

Design narrow gap groove suitable for dual beam laser welding thick plates with filler wire, guaranteed technological requirements of single pass multilayer welding and low deformation, increased neutral of wire and light to some extent.

设计了适合于厚板双光束填丝多层焊的窄间隙坡口形式，保证了厚板激光填丝焊的单道多层焊与低变形工艺要求，并一定程度上提高了丝与光对中性。

Measurement of the Film Thickness of the Oblique Line Groove Gas Face Seal

直线槽气体端面密封流体膜厚度的测量

When the thread groove width reduces, the flow rate range declines obviously, and the efficiency under same flow rate enhances;

螺纹槽宽减小，流量范围明显下降，相同流量下的效率有所增大；

In this paper, according to the urgent need of the NC machining technology, which repairs the thread groove of the screwed workpieces, the theory of tracking screw thread technology is put forward.

本课题根据当前石油钻井行业对已有螺纹工件的螺纹牙型重新修复的数控加工技术的迫切需求，提出了螺纹跟踪技术理论。

Currently, according to the urgent need of the NC machining technology, which repairs the thread groove of the screwed workpieces in oil industry, it is very important to study the technology of repairing screw thread.

目前，石油行业迫切需要数控加工技术对螺纹牙型进行修复，因而，研究螺纹修复技术具有十分重要的意义。

Milling mechanism of the indexable three-dimensional complex groove milling insert and CAD/ CAM technique are the kernel problems in the complex groove milling insert study.

可转位三维复杂槽型铣刀片的铣削机理和CAD/CAM技术是复杂槽型铣刀片的研究重点。

Firstly, parametric model of three three-dimensional complex groove milling insert is formatted by ANSYS' inner developing tools ( ANSYS Parametric Design Language, APDL and User Interface Design Language, UIDL), which provides solid model for finite element analysis.

首先，利用ANSYS的内部开发语言APDL和UIDL建立了三维复杂槽型铣刀片的参数化模型，为有限元分析提供了实体模型。

For level VII ( nodes located in tracheoesophageal groove), minimal diameter ≥ 5 mm was used as diagnostic threshold of CT, the sensitivity was 69.23%, specificity was 100%.

以淋巴结最小径≥5mm为气管食管沟区转移淋巴结的CT诊断阈，敏感性69.23%，特异性100%。