groove angle的例句大全

An Analysis of Groove Angle on the Column Intersection Line and Its Cutting

圆柱相贯线焊接坡口角及切割的分析

The joint shapes suited for CO_2 welding are designed Under which weld quality is still assured but the groove angle and size of fillet weld are reduced. By ways of these the productivity is increased and cost decreased.

提出了适合于CO2焊特点的接头形式，该接头形式在保证焊接质量前提下，减小了对接焊的坡口角度及角焊缝的焊脚尺寸，可以提高焊接生产率，降低成本。

New Method of Machining Internal Spiral Groove of a Big Lift Angle

大升角内螺旋槽加工新方法

Mathematic Modeling and Machining Method of Changed Angle and Variable Pitch Spiral Groove

变倾角变导程螺旋槽的数学建模和加工方法

On the choice of groove parameters, the influences of groove parameters ( such as groove depth, groove opening angle and groove root radius) on the groove bottom stress concentration extent were analyzed by finite element method.

在切口参数的选择上，本文使用有限元方法分析了切口深度、切口张开角度及切口根部圆角半径等对切口处应力集中程度的影响。

Welding parameters such as angle of bending tip, pulse voltage, wire feed rate, pulse mode, size of groove and welding speed can affect the appearance of weld.

导电嘴弯曲角度、送丝速度、峰值电压、协同模式、焊接速度和坡口尺寸均会对窄间隙焊缝成形产生重要影响。

The patterns etched are of high resolution, and the groove depth and groove wall angle can be controlled with less surface stress.

具有极高的分辨率，能够控制槽深和槽壁角度，表面应力小。

the effects of contact angle, heat flux density, operating temperature and groove geometry on radial dry out point were discussed.

讨论了接触角、加热热流密度、运行温度、槽道几何对干点位置的影响。

in order to assembly antifriction bearing (18) in an accurate angle, the filling groove (34) is out of the range of maximum stress.

为了允许以精确角度组装减摩轴承（18），填充槽（34）处于最大应力的范围之外。

the optimization model of sealing ability for a bushing helical seal is presented. in this model, the maximum value of sealing coefficient is objective function, and the relative groove depth, the relative groove width and helical angle are designed variables.

以密封系数最大为优化目标函数，考虑了相对槽深、相对槽宽和螺旋角等约束条件，建立了螺套式螺旋密封封液能力优化的数学模型。

Result: 36 cases of retroauricular groove flap through this surgery were survived, and reconstituted auricles had obvious skull-auricles angle, the symmetry of reconstituted auricles were improved.

结果：36例耳后沟皮瓣均成活，再造耳有明显的颅耳角度，增强了与健耳的对称性。

Focusing on the research of some important design parameters impacting the carrying capacity of the bearing, including radial clearance, contact angle and groove radius of curvature coefficient, a detailed analysis was given, and the corresponding bearing design recommendations were presented.

着重对影响轴承承载能力的重要设计参数径向游隙、接触角、沟曲率半径系数等进行了仿真，并给予了详细的分析，提出了对应的轴承设计建议。

The relationship of these major parameters such as groove numbers and spiral angle to seal pressure is revealed and the optimized result is obtained.

分析了影响密封性能的主要设计参数如螺旋角α，槽数n等对密封压力的影响规律，得出了优化结果。

The highest of dog bone arised at the middle of slab length. The stability would increase by using edging roller with groove and slope angle.

立轧后板坯头、尾部存在不同程度的失宽，狗骨高度最大值出现在板坯中部，采用孔型立辊或锥形立辊可提高轧制过程的稳定性。

Direction of the bone groove was ante inferior to post superior, and form 30 ° angle.

骨槽方向为前下后上并与水平线成30°角。