heat release的例句大全

Study of Combustion Heat Release Rate on a High High Speed Supercharge diesel Engine of Vehicle

轻型车辆用高速增压柴油机燃烧放热规律的研究

Based on the temperature recovery method, a new model is presented to handle the latent heat release of gray cast iron during the solidification process of both primary solidification and the eutectic solidification stages.

基于潜热处理的温度回升法，针对灰铸铁凝固过程中具有初晶和共晶两个阶段的凝固特性，提出了适合灰铸铁的带共晶的潜热处理方法。

Some methods of judging heat absorption and heat release of ideal gas thermodynamical process

论判断理想气体热力学过程吸放热性的有效方法

In this paper it is discussed about heat absorption and heat release's problem on diagonal line process in temperature-entropy diagram, a better result is gotten compare with the reference.

借助于T S图讨论了P V图上准静态斜直线过程的吸放热问题，得到了此文献[1]更形象更直观的结果。

study on cai combustion heat release model in 4-stroke gasoline engine

四冲程汽油机CAI燃烧放热率模型研究

With the increase of engine load, the igni-tion timing will advance, the maximum heat release rate and the maximum combustion temperature as well as the combustion duration will increase.

负荷增大时，双燃料发动机燃烧始点提前，最大燃烧放热率增高，最高燃烧温度升高，后燃较严重。

The results indicated that n-heptane showed the two-stage auto-ignition, and heat release with low temperature reaction ( LTR) and high temperature reaction ( HTR), and heat release with HTR is consist of blue-flame reaction and hot flame reaction.

结果表明，正庚烷的燃烧过程由高温反应和低温反应两个阶段组成，高温反应阶段又可以分为蓝焰反应和热焰反应两个阶段。

The results show that, with the increase of DME proportion, inlet pressure increases, but the ignition delays, the peak in-cylinder pressure and heat release rate, peak in-cylinder temperature and peak pressure rise rate decrease, and their phases retard.

研究发现，采用同一喷嘴时，随着燃料中二甲醚比例的增加，发动机进气压力增加，着火延迟，缸内压力峰值、放热率峰值、最高缸内温度、压力升高率峰值降低，其相位延后。

Meanwhile, temperature characteristic and velocity of oxygen consumption are also studied by full-scale experiment. Using conversation of energy and estimation of chemical bond energy to obtain heat release of coal sample, the limit parameters of self-ignite of coal sample are made sure.

通过大煤样自然发火实验研究了煤样的升温速度特性、耗氧速度特性，采用能量守恒和化学键能估算法计算了煤样的放热强度，确定了煤样的自燃极限参数。

The test showed that: this model can exactly simulate the heat release procedure during hydrated reaction of cement in massive concrete. The parameters in the model can be attained easily, and it's convenient to be applied in engineering.

试验表明，该模型可准确的模拟大体积混凝土的热量释放过程，且模型参数易于获得，便于工程应用。

Overall design is introduced including volumetric heat release rate of furnace, exit gas temperature, hot air temperature, efficiency of boiler, furnace dimension, superheater, reheater, attemperator, etc.

还介绍了主要热力特性数据和总体设计，包括炉膛容积热强度、炉膛出口烟温、热风温度、锅炉效率、炉膛尺寸、特性和各受热面、调温方式等。

Study on Combustion Chamber Squish Velocity and Heat Release in a Moped 2-stroke Engine

二冲程汽油机燃烧室挤流和放热规律的研究

Since lacking of domestic experiment data on full-scale fire test, the full-scale heat release rate platform for multifunctional measurement have been built in USTC.

中国科学技术大学火灾科学国家重点实验室建造了全尺寸多功能热释放速率实验台。

Application of Heat Release Model to Swirl Chamber Diesel

涡流室式柴油机放热模型的应用研究

This would weaken or strengthen the latent heat release.

对流活动增强或者减弱又会影响其潜热的释放。

At higher thermal radiation intensity, all samples produced the heat release rate and peaks have increased, the total heat release increased, mass loss increased, but the effective heat of combustion is about the same.

在较高的热辐射强度下，所有的试件产生的热释放速率及其峰值都有所增加，总放热量增大，质量损失增多，但有效燃烧热都相差不大。

Heat release rate, average burned gas temperature and NO formation as well as turbulent burning rate, turbulent flame propagating speel and flame speed ratio in different flame zones were computed as model output.

本模型不仅可以计算出燃烧放热率，燃气平均温度，NO生成规律，还可提供各火焰区的紊流燃烧速度、紊流传播速度和火焰速比等重要参数。

Based on the indicator diagrams obtained, the maximum pressure in cylinder and heat release rate after adding additive were analyzed.

基于实测的示功图，对生物添加剂加入油品后最大缸内压力和燃烧放热率等方面做了发动机燃烧特性分析。

Analyze the regulation of cylinder pressure and heat release rate, and the characteristics of fuel economy and NOX and Soot emission.

分析了缸内压力、放热率的变化规律及燃油经济性和NOX和Soot的排放特性。

When the LPG alternating ratio is smaller, the ignition delay of pre-mixing model is longer, and the peak cylinder pressure and heat release rate are higher than those of mixing injection model, and their corresponding crank angles retard.

LPG替代率较小时，预混进气方式与混合喷射方式相比滞燃期较长，最高爆发压力和最大燃烧放热率较低，对应的曲轴转角滞后；