heat的例句大全

By using the appropriate coagent, final properties such as dynamic flexibility, tear resistance, and tensile strength are comparable or superior to sulfur-cured systems with much better heat-aged performance.

通过使用适当的活性助剂，动态屈挠性能、耐撕裂性能和拉伸强度等最终物理性能相当于或优于硫黄硫化体系，但是耐热老化性能要好得多。

In addition, the tensile strength, modulus, tear resistance and rebound resilience of M containing compound were somewhat lower than those of DM containing compound, but the former gave better heat-aging resistance than the latter.

此外.含促进剂M胶料的拉伸强度、定伸应力、抗撕裂性、弹性等均略低于含DM的胶料，而耐热老化性能却比DM胶料好。

The results showed that the reversion was reduced obviously while the elastic and heat build-up of the compound after overcuring were improved, the tear strength and abrasion resistance were enhanced.

结果表明，PK-900可以明显降低硫化返原现象，并改善过硫后胶料的弹性、生热，提高撕裂强度及耐磨性能。

Technical Design of Heat Treatment for Large Pressure Vessel ofter Welding in-situ

大型压力容器现场焊后局部热处理工艺的设计

Correlation of Heat Transfer Data Obtained by the Infrared Scanner and Temperature Sensitive Coating Techniques; Technical memorandum

由红外扫描仪和热敏涂层技术所获得的数据的相关性/技术备忘录

The manage aim of our company is to guide the industry stream and improve the technical merit with energy-efficient and environment protective heat treatment devices.

公司的经营宗旨是以节能高效、洁环保型热处理装备，引导行业潮流，提高产业技术水平。

Discussesthe design theory and technical method of heat metering.

探讨了热计量的设计理论和技术措施。

Influence of Different Heat Treatment Modes and Technical Operation on Candida Albicans Adherence to the Surface of Heat-curing Resin Base

不同热处理方式及技工操作对树脂基托表面白色念珠菌黏附的影响

Improvement of Heat Treatment Technical Process of Cobalt High Speed Steel Roller

钴高速钢轧辊热处理的工艺改进

Technical reform of the high heat furnace

高温炉的节能技术改造

Failure Analysis on Longitudinal Finned Heat Exchanger and Technical Reform

纵向翅片管式换热器的失效分析及改造措施

Study on the Coefficient of Heat Transfer of Convection in the Stage of Constant Rate of Drying

恒速干燥阶段对流传热系数的研究

According to the basic rules of response surface method and center utilized design method, response surface model for performance evaluating of electrode heat convection is built. Leading in the variance analysis and F test, validation of model significance is done.

根据实验回归分析的响应面法和中心组合实验设计法的基本规则，建立面向冷却率的电极对流换热性能评价的响应面模型，并引入方差分析和F检验，验证模型的显著性。

Identification of Cooling Characteristics on a Test Probe Surface by Inverse Heat Conduction Problem

利用IHCP对淬火测试探头表面冷却特性辨识的研究

Heat transfer in the high flux engineering test reactor

高通量工程试验堆内的传热

Decay Heat Character of Fast Test Reactor after Shutdown

实验快堆停堆后衰变热特性

Through observation to the broken section and sampling test, the shaft's material and heat treatment are analyzed and it is pointed out that the main reason for the shaft breaking are bad chemical content and the unreasonable heat treatment.

通过断面观察与取样化验，分析主轴的材质及热处理状况，指出不良化学成分和不合理的热处理工艺是断轴的主要原因；

The Heat Treatment Process Test of Starting Spring of The FQ Type Engine

FQ型发动机启动器弹簧片的热处理工艺

Novel Moisture Soaking Techniques Of Soldering Heat Test for Surface Mount LSIs

新的表面安装LSI耐焊接热试验加湿技术

The temperature of the liquid and test section surface and heat transfer coefficients, with and without acoustic cavitation, were measured and analyzed in order to study the effect of the parameters of acoustic cavitation on natural convective heat transfer.

实验中测量并研究有无声空化作用时液体温度、加热表面温度及传热系数的变化，旨在研究声空化参数对自然对流传热的影响。