heating process的例句大全

Revamping of Fans of High-pressure Air-cooled Heat Exchanger of Hydrocracker The optimization of the electric heating for melting the frost in the air conditioning process

加氢裂化装置高压空冷器风机的改造电加热融霜在冷风机融霜过程的优化

The heat transfer mode described in this paper is used to research the heat conduction process of coal in coke oven chamber through the heating wall. The numerical solution of the model uses finite difference method by electronic computer.

传热模型用于研究焦炉炭化室内煤料通过炉墙的导热过程，模型用有限差分法由电子计算机进行数值解。

During the pre-onset period, the warming over the SCS monsoon region is mainly due to the warm horizontal advection and diabatic heating ( latent heat) processes, meanwhile the warming is suppressed by the vertical adiabatic process ( cooling).

夏季风爆发前期，南海季风区的增温主要由暖平流及非绝热加热过程（主要为凝结潜热）共同作用所致。

It almost forestall the international market, but its process is still in secret. There are a long distance between China and overseas in the performance of MoSi_2 heating element.

世界上生产MoSi2发热元件的厂家中以瑞典的康泰尔（Kanthal）的产品质量最好，几乎垄断了整个国际市场，但其生产工艺至今保密。

Presents different PE-X pipes and their quality control in manufacturing process. Puts forward some noticeable issues in the application of PE-X pipes to floor panel heating systems.

介绍了不同交联类型的PEX管材及其生产过程质量控制问题，同时提出了PEX管材应用在地板辐射供暖工程中应注意的问题。

According to austenite isothermal transformation diagram, a heat treatment process for producing the left and right pincers through fixed heating time and the position was put forward.

借助奥氏体等温转变曲线，创立了定时定位的热处理工艺方法，用于左右钳口的生产，一次达到设计要求，简便可靠，省时节能。

The challenge associated with establishing the necessary thermal process is maintaining a high-temperature environment around the container for a duration of time needed to meet the minimum process at the slowest heating location in the container.

与达到要求的热处理条件有关的挑战是维持高温环境达到一定的所需时间，使容器内传热比最差的点满足最低的加热处理条件。

In the process of development of solar architecture, the way how to integrate the solar air heating devices into the building is a problem.

在太阳能建筑的发展过程中，亟需解决太阳能与建筑一体化的问题。

Taking a certain engineering project for example, introduces characteristics, pipe material selection, system design, construction process, and some notices of low temperature hot water floor panel heating.

以某工程为例，介绍低温热水地板辐射采暖的特点、管材选择、系统设计、施工步骤及注意事项等。

Installation Process and Quality Control about Low Temperature Hydrothermal Water Radiant Floor Heating

关于低温热水地板辐射采暖的安装及质量控制

These advantages make it possible to become the ideal means of stabilizing process heating of the blank.

这些优点使感应加热成为当今坯料稳定化处理加热的最理想的手段。

A mathematical model based on analytical numerical mixed computation method is established to simulate the thermal process in boiler heating surface.

对锅炉热力过程采用解析&数值混合计算方法建立了计算数学模型。

Simulated bed temperature change curve shows this process consists of three stages: pure heating up stage of hot gas to coal particles, rapid increasing stage of bed temperature after coal particles begin to combust and normal operation stage characterized by slow temperature change.

研究表明流化床锅炉启动过程分为三个阶段：热气体对床料的纯加热阶段、煤颗粒燃烧后的床温快速上升阶段和床温变化平稳的正常运行阶段。

In order to improve productiveness, the liquid temperature should be maken arrive predetermine value as short time as impossible, and controlling accuracy should be ensured at the same time. For the purpose, an optimum scheme of dynamic heating in all process is presented.

在确保恒温精度的同时，为了在尽可能短的时间内使液体温度达到预定的温度，以提高工作效率，提出了全程动态加热方案。

The effects of convective thermal losses on the thermal behavior of thin metal films, as described by the microscopic hyperbolic two-step heat conduction model, are investigated based on the condition that the duration of heating source is much less than the duration of the thermalization process.

在激光热源加热时间远小于达到热平衡所需时间的条件下，研究了对流热损失对金属薄膜热行为的影响。

Mechanism, parameters and advantages of a deburring process by heating are described, by which process burrs on silicon steel sheets and on the edge of Aluminium guide strips of the motor rotor are removed through heating.

本文介绍了一种脱壳去毛利工艺，即用加热法去除电机转子硅钢片和铝导条边缘毛刺工艺的机理、参数及优点。

Spang Power Electronics designs AC power centers to precisely match the characteristics of specific heating elements and process requirements.

斯潘AC电源电力电子设计中心，工艺要求精确匹配的特点和具体的加热元件。

Heating of air, suited to drying up certain powder, chemical engineering process and jet drying under certain pressure.

空气的加热，适用于一定压力下，一些粉末干燥、工过程及喷射干燥。

The results show that the fine cracks are evolved from surface gas holes of steel billet in the process of high temperature heating and rolling.

结果表明，发纹缺陷是由方坯表面气孔经高温加热→轧制演变成的。

A New Process of Preparing High-purity Molybdenum Trioxide by Microwave Hybrid Heating

微波混合加热制备高纯三氧化钼新工艺