heating process的例句大全

Verification indicate this simulation system can simulate slab heating whole process and optimize slab running velocity and temperature condition schedule of furnace operation and provide on-line control with optimum data.

验证表明，该系统能有效地模拟钢板在炉内加热升温的全过程。可以对炉辊速度和炉区温度进行寻优计算，为在线控制提供辊速及炉温制度最佳数据。

The results may be used in heating laminating process for high temperature-resistant PPS/ GF composite materials.

玻璃化温度（T＿g）提高。研究结果为长期耐高温PPS／GF复合材料构件的热层压工艺提供技术依据。

Abstract: Glass heating in horizontal tempering furnace is a dynamic process, the system, controlling, design and install of the tempering furnace make influence of this process.

在水平钢化炉中玻璃加热是个动态的过程，钢化炉的系统、制和设计安装质量影响这一过程。

The induction heating equipment and heat treatment process of thick-wall pipe were reconstructed.

对厚壁管感应加热设备及热处理工艺进行了重新设计改造。

The Multiwell heating, throttling refrigeration and low-temperature separation process have been applied in the gas gathering station of the Yulin gas field.

为彻底解决该问题，先后在榆总站建设了两套大面积换热、节流、低温分离工艺装置，并在现场进行了工业性试验。

Discussing on Choosing and Arrangement the Burner Using in Big Car Type Heating Furnace Burning the Natural Gas Transfer case sprocket production through the sinter hardening process

大型天然气台车加热炉烧嘴选型及布置的探讨用烧结硬化工艺生产汽车分动箱链轮

Mechanism, parameters and advantages of a deburring process by heating are described, by which process burrs on silicon steel sheets and on the edge of Aluminium guide strips of the motor rotor are removed through heating.

本文介绍了一种脱壳去毛利工艺，即用加热法去除电机转子硅钢片和铝导条边缘毛刺工艺的机理、参数及优点。

According to austenite isothermal transformation diagram, a heat treatment process for producing the left and right pincers through fixed heating time and the position was put forward.

借助奥氏体等温转变曲线，创立了定时定位的热处理工艺方法，用于左右钳口的生产，一次达到设计要求，简便可靠，省时节能。

The heat transfer mode described in this paper is used to research the heat conduction process of coal in coke oven chamber through the heating wall. The numerical solution of the model uses finite difference method by electronic computer.

传热模型用于研究焦炉炭化室内煤料通过炉墙的导热过程，模型用有限差分法由电子计算机进行数值解。

The effect of preheating treatment process of cold rolls on induction heat quenched structures and the effect of heating temperature and time on structure and hardness have been studied.

研究了轧辊的预备热处理工艺对感应加热淬火组织的影响，感应加热温度和时间对组织和硬度的影响。

In addition, the U-shaped interface, which minimizes electron crowding and localized heating effects, increases the mean time to failure by electromigration. Consistent, repeatable blanket film property and good parametric electrical test results have proven the production worthiness of this process.

此外，使电子阻塞和局部加热效应最小化的U型界面，提高了电子迁移失效的平均时间，一致的、可重复的覆盖膜特性和良好的电参量测试结果已经证实了这种工艺的生产价值。

Analyzing the transformation mechanism of titanium and titanium hydride. It makes the use of the fact that titanium hydride releasing hydride at 300 ℃, to design and process the Hydrogen Generator as well as its heating circuit.

详细分析了钛与氢化钛的转化机理，并利用氢化钛在350℃放氢的原理制作了氢发生器，以及其加热电路，并加工测试。

Thermal cycling absorption process ( TCAP) in a full reflux mode was studied at different feeding ratios, feeding places and heating/ cooling temperatures.

分别在不同进料比、进料位置、加热/冷却温度的条件下，对TCAP工艺的全回流模式进行了实验。

Due to a great deal of limitation of heating by flame or laser, a new thermal stress forming process& high frequency induction heating forming of plate is studied in this paper.

由于火焰或激光局部加热存在着诸多局限性，因此本文研究了一种新的板料热应力成形技术&高频感应弯板成形工艺。

The mechanical shock and thermal impact in the machining process of discontinuous grinding polycrystalline diamond with slotted diamond wheels were investigated systemically by the simulation experiments of ultrasonic vibration and pulse laser heating respectively.

分别采用超声振动冲击和脉冲激光加热技术对开槽金刚石砂轮断续磨削加工聚晶金刚石过程中的机械冲击和热冲击进行了模拟实验研究。

The calculating process of energy, collector's thermal loss coefficient, exporting temperature for CPCs used in large-scale solar system was developed. Then, an example of the research on matching of CPCs in solar water heating system was showed.

对于应用于大型太阳能系统的CPC集热器阵列，提出计算其能量、集热器热损失系数、出口水温等参数的计算方法，并以某太阳能热水系统的CPC阵列为例进行了计算。

The effects of convective thermal losses on the thermal behavior of thin metal films, as described by the microscopic hyperbolic two-step heat conduction model, are investigated based on the condition that the duration of heating source is much less than the duration of the thermalization process.

在激光热源加热时间远小于达到热平衡所需时间的条件下，研究了对流热损失对金属薄膜热行为的影响。

Taking a certain engineering project for example, introduces characteristics, pipe material selection, system design, construction process, and some notices of low temperature hot water floor panel heating.

以某工程为例，介绍低温热水地板辐射采暖的特点、管材选择、系统设计、施工步骤及注意事项等。

Presents different PE-X pipes and their quality control in manufacturing process. Puts forward some noticeable issues in the application of PE-X pipes to floor panel heating systems.

介绍了不同交联类型的PEX管材及其生产过程质量控制问题，同时提出了PEX管材应用在地板辐射供暖工程中应注意的问题。

Revamping of Fans of High-pressure Air-cooled Heat Exchanger of Hydrocracker The optimization of the electric heating for melting the frost in the air conditioning process

加氢裂化装置高压空冷器风机的改造电加热融霜在冷风机融霜过程的优化