hobbing的例句大全

Many failure modes of the clod hobbing die are relative to the potential wrong design, wrong manufacturing and wrong fit of the mould.

冷挤压模具在设计与生产制造过程中存在着多种失效形式，而每种失效形式都和潜在的不合理设计、制造以及装配有关。

The paper, based on analyzing the errors in clamps for gear hobbing machine and gear slotting machine when positioning and tool-setting, proposes to use several important gearing tolerances to limit the errors in clamp when positioning and tool-setting.

重点分析常用的加工齿轮的滚齿机和插齿机夹具在机床上定位和对刀误差，并用常用的几个重要的齿轮公差来限定机床夹具的定位和对刀误差。

This is a study of mathematical model and principle of applied spiral Cutting non-circular on the machina of procedure-Control hobbing gear

应用渐开线滚刀在数控滚齿机上展成加工非园齿轮原理和数学模型的研究

Then the formulae for calculating machine tool adjustment parameters on hobbing are derived by the study of spatial meshing principle among hobbing cutter, imaginary generating rack and gear.

进而通过对滚刀、产形齿条及锥形齿轮三者之间空间几何关系的分析，从理论上阐明了锥形齿轮的滚齿加工原理并推导了机床调整参数的计算公式。

This paper is to put forward a method for hobbing helical gear with small lead angle, and a method of calculating adjustment accuracy of machine.

本文通过对滚齿机滚切斜齿轮原理的分析，提出了滚切小螺旋角斜齿轮的方法以及机床调整精度的计算方法。

Selecting the gear change of the helical hobbing chang gear by using the program

用计算器编程选择斜齿滚削挂轮

Application of Hobbing Drill Bit in The Piling Construction

滚刀钻头在桩基施工中的应用

Calculation of Reasonable Allowance on Change Gear Ratio in Gear Hobbing Adjustment

滚齿调整中挂轮比允差的计算

Tooth Profile Design of Hobs for Hobbing Regular Polygon Workpieces

滚切正多边形工件的滚刀齿形设计

Skiving quenched gear teeth surface with hard alloyed hobbing cutter

用硬质合金滚刀刮削硬齿面

At present it offers equipment for many gear manufacturing stages such as hobbing, shaping, hard skiving, shaving, honing, and milling.

目前，它提供为齿轮加工的各阶段比如滚齿，成型，硬切削，剃齿，珩磨和磨齿等而制造的设备。

At present, traditional processes of hob are radial relief grinding in general, when we adopt this process, it will cause tooth flanks distortion, reduce hob proper tooth profile, and be lead to hob accuracy lower, which restricts gear hobbing level further seriously.

目前滚刀一般采用径向铲磨方式进行精加工，由于径向铲磨会造成齿侧面畸变，减小齿形合格长度，导致滚刀精度寿命低，径向铲磨工艺严重制约着滚齿加工水平的进一步提高。

Meantime, a general principle system of CNC simultaneous control for hobbing noncircular helical gears is designed.

同时设计出非圆斜齿轮滚切加工CNC联动控制的一般原理图。

False signal and its filtering in position measurement on hobbing

滚齿机位置测量中的假信号与滤波

Designing special tooling for machining interal gear on gear hobbing machine

在滚齿机上设计专用工装加工内齿轮

The worm gear produced by new process has been successfully used in precision hobbing machine.

用新工艺加工的球面蜗轮副已成功地用作精密滚齿机的分度副。

The method of helix angle choosing of involute gears do not ensure hobbing precision. It cause large lead error.

这种选择往往在齿轮滚齿加工时，不能保证螺旋角β的精度，因而引起螺旋线偏差过大，接触时往往达不到全齿长的接触。

The manual programming method of gear hobbing, which uses manpower to carry on processing procedure, computing, compiling programmings, inputing programmings, checking programmings and so on, usually leads to huge calculating work, high error rate and low efficiency.

齿轮加工采用手工编程需人工进行工艺处理、数值计算、编写程序、输入和校验程序等步骤，其计算量大，出错率高且编程效率低。

A New Apparatus for Hobbing Crown Gear Based on Conjugate Principle

按共轭原理滚切鼓形齿轮的新装置

The paper introduces a rapid calculation for gear change using ordinary function calculation in hobbing cylindrical straight gears with a teeth number greater or twice than a prime number over 100. This calculation method is simple, convenience and practical.

介绍了一种用普通函数计算器快速计算滚切齿数大于100的质数及其整数倍的直齿圆柱齿轮的挂轮。