hot process的例句大全

the succession pattern and process of plant community and their environments is a hot spot in community and ecosystem dynamic study.

植物群落及其环境在干扰后的演替格局和过程的研究，是群落和生态系统动态研究的一个热点。

hot spinning process of titanium alloy collar rim of lunar rover

月球车钛合金轮圈的热旋压成形工艺研究

design of large hot-box process mold vent system

大型热芯盒模具排气系统设计

design of hot-box process mold for resin-sand core

树脂砂芯热芯盒模具设计

analysis on hot die-forming process simulation for upper core plate

上心盘热模压成形过程的模拟分析

industry: hot rolled steel plate; cold-rolled steel plate; steel (roll) material; smelting process;

所属行业：热轧钢板；冷轧钢板；钢带（卷）材；冶炼加工；；

nd process hot water system

工艺热水系统

in this paper, sic particulate reinforced magnesium matrix composites were prepared by conventional hot press sintering process and specimen current heating hot press sintering process.

本文采用电流直加热法和普通热压法，以纯镁为基体，以SiC颗粒为增强相，制备了SiC颗粒增强镁基复合材料。

The process is called heat acclimation and is routinely seen in athletes training in hot weather.

这过程称为热适应,最常见于在大热天里受训的田径选手.

Thethe hot crimping process and its test methods for the vehicle thrust rod.

主要介绍汽车推力杆的热铆接工艺及其试验方法.

The hot-rolling process and parameters for JL 510 L automobile beam steel are introduced.

介绍了唐山建龙实业有限公司JL510L汽车大梁钢的热轧工艺及其参数控制.

They are usually carried out industrially by pack cementation or hot dip process.

目前工业上常用的渗铝方法有固体包装法和热浸法.

This research mainly investigates the hot extrusion process of AZ 61 magnesium alloy bicycle carriers.

本论文主要针对AZ61镁合金脚踏车携车架之热间挤制加工之研究.

Figure 16 – Schematics of the encapsulated Hot Isostatic Pressing process.

图16-示意图的封装热等静压过程.

Hot forming of stainless steel elliptical head is specifical process.

对不锈钢椭圆封头,其压制工艺过程特殊.

Synopsis There are some factors that cause the formation hot strip side-camber in the rolling process.

板带轧制过程中因受某些因素影响会形成侧弯.

Hot stamping process for four basic conditions: includes hot stamping templates, heater, and pressure shipping agencies.

烫印工艺的四个基本条件: 烫印头包括烫印模版, 加热器, 及压力传送机构.

The resin-matrix pantograph contact strip ( RMPCS ) was prepared by using hot re-pressing and vacuum-impregnation process.

采用二次热压和真空浸渍工艺制备树脂基受电弓滑板试样.

The direct contact heat transfer process was studied in a vertical pipe of a looper with coolant pentane and hot water system.

在一气升式外循环实验设备中研究了冷剂正戊烷与热流体水在垂直管内直接接触汽化传热过程。

According to the process control of hot-mixed asphalt mixture, this paper analyses the problems and control measures on the uniformity and mix accuracy of hot-mixed asphalt mixture in production.

针对热拌沥青混合料生产的过程控制，结合工程实践，论述了生产过程中沥青混合料的均匀性和配合比准确性等应注意的问题和采取的措施。