ignition temperature的例句大全

the characteristics of this new combustion system are low cylinder pressure, rapid mixing, long ignition delay period and low combustion temperature.

此燃烧系统所具有的特征是：低爆压、快速混合、滞燃期长和低温燃烧。

the results show that as the load increased, the combustion ignition delay was decreased, and cylinder temperature, pressure, heat release rate, soot and no emissions are increased.

结果表明，随着负荷的增加，燃烧滞燃期缩短，缸内温度、压力、放热率、Soot和NO排放均增加。

in addition, an auto-ignition model based on the multi-step dme/ air chemical kinetic mechanism was developed and an ignition delay data library was generated using the computational results of dme ignition delay correlated against temperature, pressure and fuel/ air equivalence ratio.

另从二甲醚低温着火的化学反应机理入手，开展了其自燃着火过程的数值模拟研究，进而建立了计及温度、压力和燃空当量比因素的DME滞燃期数据库；

When to close before dawn, the temperature of ignition reduces, the skin also tends an alkalinity.

到了接近凌晨时, 温度开始降低, 皮肤也趋于碱性.

High temperature air non-oil ignition is the advanced burning technology with vast prospect.

高温空气无油点火技术是一种先进的燃烧技术,具有广阔的应用前景.

The kaolinite may clag the ignition of coal, when the amount of kaolinite ratio is in 50%-60%, the kindling temperature is about 9 ℃-13 ℃ higher than single coal, and the stability of combustion decreases.

煤样的着火点逐渐升高，当高岭石的添加量在50%～60%之间时，着火温度约升高9℃～13℃，燃烧稳定性也降低；

And increasing ignition energy can fulfill request of in-cylinder lower mixture temperature.

提高点火能量能降低对缸内温度的要求.

The coolant temperature, intake port deposit, cranking speed and ignition timing all influence the limit with various mechanisms.

拖动转速、冷却水温度、进气道油膜残留和点火时刻等燃烧边界条件都对窗口区域造成影响。

The results show that low pressure natural gas supply can easily realize the premixed charge compression ignition of the natural gas engine on condition of heating the intake air and increasing the temperature of the electrical glow plug.

试验结果显示：在进气加热和电热塞辅助加热的情况下，低压预混合供气较易于实现压缩着火，适当增大主副燃烧室通道孔径也有助于压缩着火天然气发动机起动。

dilution can increase the ignition delay, slow down the oxidation rate of the fuel, and reduce the maximum combustion temperature.

稀释作用可以增加滞燃期，减缓燃料的氧化速度，降低最高燃烧温度。

The curves of heating temperature vs the loss of ignition ( LOI) of some kinds of used resin bonded sand are shown by laboratory testing the LOI under given heating temperature and time.

通过在实验室条件下对树脂旧砂在一定加热温度、加热时间下燃烧减量的测试，建立了几种树脂旧砂加热温度和燃烧减量之间的关系曲线；

The results show that, with the increase of DME proportion, inlet pressure increases, but the ignition delays, the peak in-cylinder pressure and heat release rate, peak in-cylinder temperature and peak pressure rise rate decrease, and their phases retard.

研究发现，采用同一喷嘴时，随着燃料中二甲醚比例的增加，发动机进气压力增加，着火延迟，缸内压力峰值、放热率峰值、最高缸内温度、压力升高率峰值降低，其相位延后。

Ignition electronic module Temperature test Environmental temperature;

点火电子组件；温度试验；环境温度；

The critical temperature of propellant is 520~ 525K and the delay time of ignition decreases with increasing the outside flame temperature.

推进剂产生热危险性的临界温度为520~525K；在外界火焰作用下，发动机内的推进剂将点火燃烧，随着外界火焰温度的上升，推进剂起始燃烧的延迟时间减少。

The local temperature and concentration of fuel vapor in the cylinder is an important factor, which affects the process of ignition and combustion of diesel engine. Investigation on the distribution of temperature and concentration in a diesel spray has practical significance.

柴油机缸内局部燃油蒸气的温度与浓度是影响柴油机着火与燃烧的重要因素，因此研究喷雾油束内燃油温度与浓度分布具有一定的实际意义。

An ignition of pulverized coal by high temperature air

粉煤高温空气无油点火

By using thing this model, the effects of the temperature of oxygen-acetylene torch, diameter of coal particle and quality of coal on ignition are predicted.

利用该模型，还预测了点火源温度、煤粉粒径以及煤中挥发份含量对煤粉气流火炬点火的影响。

Conduct the ignition in a well-ventilated hood, but protected from air currents, and at as low a temperature as is possible to effect the complete combustion of the carbon.

在通风良好的罩子里进行灼烧，但须防止其接触气流，并且在尽可能低的温度进行，以便使碳实现彻底燃烧。

The experimental results show that the large size controllable vortex above the stock produced by dipole vortex device gets up the transfering ability of high temperature gas to the area of fuel ignition, and about 3~ 4 times than the conventional rear arch.

试验表明，偶极子涡流器在炉排上部产生的大尺度可控旋涡提高了向燃料着火区输送高温烟气能力，约比传统后拱的输送能力提高2～3倍。

the factors affecting the reduction process in smelting magnesium include hydration activity of the calcined white, loss of weight on ignition, imbibition, burden, size reduction, density of pellet, reduction temperature, reduction duration, and vacuum level.

影响皮江法炼镁的还原工序的因素有煅白的水化活性度、灼减、吸湿，球的配比、炉料的粉碎粒度、制球后球团密度和还原温度、还原时间、真空度等。