impact test的例句大全

Study of drop hammer plastic deformation at engineering vehicle FOPS impact test

工程车辆FOPS冲击试验中落锤塑性变形研究

A method to confirm impact stiffness& wave combination method by drop hammer impact test machine is introduced.

介绍一种确定隔振器冲击刚度的新方法&波形组合法。

The method of tempered glass impact test ( 227g steel ball test)

GB/T2843-1981钢化玻璃抗冲击性试验方法（227克钢球试验）

The Effect of Different Directions Impact Test of Controlled Rolled Steeled Plate on Fracture Separation

控轧钢不同取向冲击试验对形成断口分离的影响

New development of impact on the test standard impact test-instrumental method for metal material

冲击试验的新发展

Delimitation of Impact Testing Range of Flight Test Missile

飞行试验弹落点检验域的划定

Tensile test, impact test have been carried out for the three alloys.

对三种合金分别进行了拉伸、冲击试验和断口分析。

In the projectile impact test, the front sheet fails by mainly local indentation and insertion, and the rear sheet shows the global deformation of "dome" form, local partial tear and even penetration.

子弹撞击作用下前面板主要有压入、撕裂和嵌入失效，后面板为穹形整体变形以及局部的撕裂直至穿透。

Impact test for FRP antenna on ultra-short wave wideband carborne radio station

超短波车载电台宽频带玻璃钢天线撞击试验

Experimental data were obtained by means of all kinds of instruments such as a tensile machine, an Izod impact test machine, thermogravimetric analysis, limit oxygen index ( LOI) instrument and so on.

各种数据的获得借助于拉力试验机、悬臂梁冲击试验机、热重分析仪、和氧指数仪等各种分析测试手段。

Impact toughness of HP295 steel plate were investigated at different finishing temperature and test temperature by means of instrumented impact test.

应用示波冲击试验技术测量了不同终轧温度下HP295钢板在系列温度下的冲击韧性。

Prediction Between Instrumented Impact Test and Three-Point Bending Fracture Toughness Using Local Approach

基于局部法示波冲击与三点弯曲断裂韧性相互预测

The mechanical properties, microstructure and toughing mechanism of the composites were investigated by three-point bending test, impact test and scanning electron microscopy.

通过弯曲性能测试、冲击性能测试以及断面SEM形貌分析来研究复合材料的力学性能、微观结构以及增韧机制。

The Impact Test Study of the Improved Middle Traffic Guardrail on the Viaduct Roads

内环线高架道路中间隔离护栏结构改进形式的冲击试验研究

The context were set in three different conditions, first, the model of impact were raised to the desired height, and then released so that the drop hammer make the gravity acceleration to impact test beam.

本文共设置了三种不同的工况，首先将落锤分别提至所需高度，然后释放使落锤在重力作用下作加速运动撞击试验梁。

Charpy Impact Test Tolerance Analysis of Spiral Welded Pipe

螺旋焊管夏比冲击试验误差分析

Impact Test for Car-Body Member Parts

车体构件的冲击试验

remove the sight control circuit packaging intact were the high-low temperature impact test;

将瞄准镜控制电路取下，包装完好分别进行高低温环境冲击试验；

Through the repeat impact test of coating workpieces and comparison between the changes of coating and base thickness under different impact times, it is finded that under impact stress even less than yield limit, material of workpieces appeared macroscopical plastic deformation.

通过对带涂层试样的多冲试验，对不同冲击次数下涂层和基体的厚度变化进行对比，发现即使在低于材料屈服极限的冲击应力下，材料也会产生宏观塑性变形。

Frontal Pendulum Impact Test and Computer Simulation of Commercial Vehicles

商用车摆锤正面撞击试验和仿真