impeller pump的例句大全

Single suction, single stage horizontal centrifugal pump with closed impeller.

单吸 、 单级卧式离心泵,用封闭叶轮.

Two . Pump impeller loose ground to pump out the bottom end caps.

水泵叶轮松动,磨到水泵出水底端盖.

The impeller of the sea water pump is unevenly worn out.

海水泵叶轮严重单边磨损.

Excellent water cycle system, Adopting large impeller water pump, make sure the whole engine heat emission.

优化的水循环系统, 采用大叶轮水泵,提高了低速泵水的能力, 保证了整机的散热效果更好.

Through analyzing, it is showed that the major factors which influence the performance of the pump are the shape of axial section flow channel, the hydraulic parameter of impeller and guide blade and the geometric parameter of the inlet conduit.

论文通过分析，得出影响其性能的主要因素有泵的轴面流道形状、泵的叶轮、导叶的水力参数以及进水流道的几何参数。

It discusses the effects of using impeller sealing ring to regulate axial force of turbo pump.

从分析某汽轮给水泵机组轴承磨损故障入手,阐述了利用叶轮密封环调节汽轮给水泵的轴向力的作用和效果.

The axial force of pump is balanced by balancing ring on impeller.

泵的轴向力由叶轮设平衡环来进行平衡。

Flow field of centrifugal pump ( Pump flow passage includes suction pipe, impeller and volute casing.) was obtained by solving the Reynolds average Navier-Stokes equation.

通过求解包括进水管、叶轮、泵体等过流部件在内的水泵流道内的三维稳定雷诺平均Navier-Stokes方程，获得水泵内部的流场分布特征。

The composing, function, selecting principle and key of parts of the pump, such as electromotor, axle-jointer, bearing box seat, water cooling seal cavity, down pump body, pump axle and impeller, are introduced in detail by pump body structure diagram.

给出泵体结构图，详细介绍泵的电机、联轴器、轴承箱座、水冷密封腔、下泵体、泵轴、叶轮等部件的组成、功能，各部件的选型原则和关键点。

After investigating the concave exit edge of slurry pump impeller, the paper points out the possibility to improve the flow passage wear of slurry pumps in the hydrodynamics point of view.

通过对渣浆泵转轮的凹形叶片出口边的研究，从流体动力学的角度指出了改善渣浆泵过流部件磨损情况的可能性；

Reverse design and process simulation of dredging pump impeller

疏浚泥泵叶轮的反求设计及加工仿真

A particular sludge agitator for oval sludge digester has been designed and made up on the basis of the theory of axis pump impeller and inducting principle against the cavitations erosion of pump.

根据轴流泵叶轮和水泵提高抗汽蚀性能的诱导轮等设计方法，设计出了新型卵形污泥消化池搅拌机。

Dredging Pump flow pump components mainly composed by Shell, impeller, the former liner and after liner.

挖泥船泥泵过流部件主要由泵壳 、 叶轮 、 前衬板和后衬板等组成.

It is not only used to design centrifugal pump impeller and diffuser, but also used to design non_clogging pump impeller and diffuser, radial diffuser, space diffuser, etc.

它除了可进行清水泵的叶轮、蜗壳水力设计外，还可设计无堵塞泵的叶轮、蜗壳以及径向导叶、空间导叶等水力件的水力设计。

The three main problems faced by water pump are leakage, vibration noise and corrosion of the impeller and water cavity wall.

汽车水泵的三个主要故障是泄漏、振动噪声和叶轮或水腔内的腐蚀。

The of the pump impeller, the boards are manufactured using wer-resistant alloy .

该泵泵体、叶轮 、 护板均采用 耐磨合金 制造.

Centrifugal pump impeller in general many such.

一般的离心泵叶轮多为此类.

Self-priming centrifugal pump over-current components are: inhalation room, impeller, the chamber pressure is in three parts.

自吸离心泵的过 流部件 有: 吸入室, 叶轮, 压出室三个部分.

And then removed the pump shaft shell removed send impeller repair shop repair.

然后将轴拆出泵壳，拆下叶轮送修理厂修理。

Basic structure of the centrifugal pump is composed of six parts, namely: impeller, pump, pump shaft, bearing, seal ring, stuffing box.

离心泵的基本构造是由六部分组成的，分别是：叶轮，泵体，泵轴，轴承，密封环，填料函。