ingot的例句大全

In the process of multi-heat teeming in heavy ingot, the tundish acts as an intermediate vessel which connecting the ladle and ingot mold, storing liquid steel to ensure the multi-heat teeming when ladle is changing.

在多炉连浇大型钢锭过程中，中间包是连接钢包与钢锭模之间的中间容器，其主要功能为贮存一定量的钢水，以保证在更换钢包时实现多炉连续浇注。

The calculated temperature field of solidification of 60t ingot conforms to the trend of solidification of ingot.

60t钢锭的计算温度场符合钢锭的凝固趋势。

Numerical calculation and Application on temperature field of steel ingot solidification procedure by boundary element method

边界元法对钢锭凝固过程温度场的数值解析与应用

It provide a scientific basis for the electrode melting velocity control and the temperature control of the ingot solidification process, and have a certain value for the actual production.

本文采用的研究方法为目前国内铸造行业研究的热点，为电极熔速的控制和钢锭凝固过程温度控制、结晶器设计等提供了科学依据，对实际生产工程有一定的应用价值。

Analysis of the Temperature of Slabs out of CCM in HCR Technology The Technology Research of Semi-solid Forming Pulps and Ingot Which are Made by Strong Cooling with Single-tube

热送热装工艺中板坯出连铸机温度的分折单管强冷制备半固态成形浆料及坯料的工艺研究

A two dimensional mathematical model for ingot solidification has been established and new methods such as revised temperature recovery method, mean boundary radiation thermal flow and variable time-step length by zone have been applied in this paper.

本文建立了钢锭冷凝过程的二维数学模型，采用了修正温度回升法、平均边界辐射热流、分区变时间步长等新方法。

Quantitative analysis of benefits of charging temperature of steel ingot of soaking pit

钢锭模准备和脱锭跨均热炉钢锭装炉温度效益的定量分析

Test of Raw Lead Ingot Mould Made of Low-Alloy Cast Iron

低合金铸铁粗铅锭模的试验

To eliminate the pore defects in ingot by hot forging process, the closure of pores in solid cylinders undergoing hot forging is numerically simulated by thermomechanical coupling finite element method.

为了在锻造过程中消除锻件内部的空洞型缺陷，采用热力耦合有限元法模拟了各种条件下圆柱体锻件中心空洞的热锻闭合过程。

Direct-reading AES analysis of tin ingot the investigation of the electroslag teeming process for production of hollow ingots

锡锭的直读光谱分析电渣浇注空心锭研究

Composition and property of tin ingot imported and domestic tin ingot are compared.

分析比较了进口锡与国产锡的成分和性能。

Study on the ICP AES Method for Determination of Microamount of Cadmium in Tin Ingot

ICP-AES法测定锡锭中微量镉的方法研究

Direct-reading atomic emission spectrometry was applied to the determination of impurity-elements in tin ingot. The analytical lines of the 9 elements determined and the analytical parameters of the determinations, including the requirements of sample preparation, and the fitting of calibration curves, were studied and optimized.

应用直读原子发射光谱法分析了锡锭中9种杂质元素，对各元素的分析线及测定的分析参数，包括试样制备的要求，校正曲线的拟合等进行了试验及优化。

Thermal conditions forming channel segregation in a steel ingot depend not only on cooling rate but also on the ratio of axial temperature gradient, GA? to radial one, GR.

钢锭中形成沟槽偏析的传热条件不仅与凝固冷却速度有关，而且取决于轴向温度梯度G A与径向温度梯度G R之比。

The procedure of thermit welding for repair of the ingot die is presented in the paper.

介绍了铝热焊修复钢锭模的工艺过程。

Repair welding of ingot die with thermit welding

铝热焊修复钢锭模

By comparison with manual arc welding, it is found that the thermit welding is a efficiency, energy saving and high quality process for repair welding of steel ingot die.

根据对比铝热焊与手弧焊修复工艺，阐明了用铝热焊修复钢锭模是一种高效、节能、焊接质量好的新方法。

Based on the corresponding relationships simple method for analysis of ingot mold Life was proposed. In addition, the influence of ingot mold geometry on the ingot mold life was studied.

本文借助该关系提出了用温度场分析锭模寿命的简便方法，并据此分析了锭模结构对锭模寿命的影响。

This paper studies the influence of the change of flow direction of cooling water at the botton of ingot mold and the mold material on the crack and the inner surface roughness of the ingot mold.

对锌锭模制造经过多次的改进试验，主要改进了锌锭模下端面的冷却水流向和材质，研究其对锌锭模的断裂、内腔表面粗糙度的影响；

Thermal fatigue is the most common failure mode of mould, especially for large ingot mold. At present, failure hot work moulds because of thermal fatigue crack account of 70% in total failure molds in our country.

热疲劳是模具最常见的失效形式，对于大锭铸模尤其如此，目前我国热作模具因热疲劳裂纹而失效的占模具失效总数的70%左右。