injection rate的例句大全

determination of water injection rate for single injection well employing dividing coefficient approach

运用劈分系数法确定注水井单井配注

the results show that the temperature rise of fluid co2 is little because of insulation measures like insulated tubing and n2 in casing annular and the temperature of co2 arriving bottom hole has larger difference as different injection rate.

计算结果表明，由于注入时间较短，且注入过程中采取使用隔热油管、环空内充氮气等保温措施，液态CO2温升较小；随着注入速度的变化，液态CO2到达井底的温度相差较大。

No matter what circumstances, fracture injection technology can improve recovery at a large extent compared to taking into injection rate decline and have broad application prospects.

不论何种情况，与考虑注入量下降情况相比，裂缝扩展注水技术能够大程度提高采出程度，有着广阔的应用前景。

influence of wellhead back pressure and gas injection rate on bottomhole pressure

井口回压和注气量对井底压力的影响

clinical study on the water injection rate of balloon indwelling catheter

留置气囊导尿管注水量的临床观察

experiment of water injection rate limit in waterflooding development in lamadian oilfield

喇嘛甸油田水驱开发注水量界限的实验

It is confirmed by laboratory test and field test that both of them have good effect on unplugging in oil well, decreasing pressure and increasing injection rate in water well, profile control at well group, reservoir sweep, and so on.

室内实验和矿场应用结果表明，在油井解堵、水井降压增注及井组调剖驱油等方面都见到良好效果。

So the injection rate should be controlled in accordance with geologic features in order to reduce the influence of the factors of shear, retension and so on on the viscosity of polymer solution and attain the goal of improving oil recovery.

因此，应根据各区块地质特点适当控制注入速度，以减少由于剪切、滞留等因素对聚合物粘度造成的影响，达到提高原油采收率的目的。

a perforated nozzle for spraying water from a hose or sprinkling can. study on the fuel injection rate of a multi-hole injector applied to a direct injection gasoline engine

莲蓬式喷嘴一种使水从管子或喷水壶里喷洒出来的有孔的喷嘴直喷汽油机多孔喷油器的喷油规律研究

Augment Piezoelectricity Common Rail Injection System with Variable Injection Rate Shape

喷油率形状可变的增压式压电共轨喷射系统

It was found that at low injection rate the tensile specimen has the best performance for both tensile strength and impact toughness; at low melt temperature, although the tensile properties of the sample is better, but its impact toughness is reduced.

研究发现，低注射速率条件下试样有最优的拉伸性能与冲击韧性；低熔体温度条件下的试样虽然拉伸性能较好，但其冲击韧性反而降低。

analysis of accuracy and improvement of maximum-slope method in ct perfusion under the condition of low injection rate

CT灌注在低注射流率时最大斜率法的准确性分析及改良

an approach to determine water injection rate in the water drive oil fields

确定水驱油田注水量的一种方法

determination of reasonable water injection rate by using capillary pressure curve

用毛管压力曲线确定合理注水强度

The rate of combustion reaction and liquid production are increased with the increase of frequency factor of combustion, decrease of activity energy, and increase of air injection rate.

增加燃烧反应的频率因子、降低活化能、增大注气速度，会加快燃烧反应，增加产液量；

The Parameters Study About Contrast Material Injection Rate and Delay Time in Spiral CT Angiography of Cerebral Vessels

螺旋CT脑血管造影造影剂注射速度与延迟时间参数研究

Studied the water shutoff method, witch pre-treatment formation with high concentration of polymer, optimize water shutoff parameters by means of perpendicularity test, including mass fraction of polymer, intake volume of polymer, injection rate of polymer and permeability.

研究了用高浓聚合物预处理地层的堵水方法，正交试验法优化了堵水参数，包括高浓聚合物质量分数、高浓聚合物注入量、注入速度和地层渗透率极差。

Huan-127 block of Liaohe Oilfield was taken as an example to design air injection rate of 25-33 well group in this block.

以辽河油田欢127块为例，初步设计了该块25-33井组的注气速度。

study on the fuel injection rate of a multi-hole injector applied to a direct injection gasoline engine

喷孔式喷油嘴喷雾器直喷汽油机多孔喷油器的喷油规律研究

Real water injection rate in water injection well will change when system pressure fluctuates or formation water absorption capacity changes. It is a disadvantage to needle vavle and downhole fixed water noddle.

注水井实际注水量随系统压力波动或地层吸水能力的变化而改变，这是针型阀或井下固定水嘴无法避免的缺陷。