inlet angle的例句大全

The inlet film thickness was defined by analyzing the inlet zone, and the influence of unsteady variables such as strip tension stress, rolling speed and inlet angle on inlet film thickness was considered.

考虑了非稳态变量如带张力、轧制速度、入口角等因素对入口油膜厚度的影响，同时还分析了入口油膜厚度的频率响应情形。

optimization on the inlet angle of flue gas for the fgd spray scrubber by the numerical simulation

湿法脱硫喷淋塔烟气入口角度优化数值模拟

under restricted air inlet condition, the inlet angle has no influence on the air side performances of heat exchangers basically.

受限进风条件下，换热器空气侧特性基本不随进风角度的影响。

In the meantime , the effect of air inlet angle on particle deposition was also researched.

同时, 研究了不同气流进口角对粒子沉积状况的影响.

In comparison with 30 ° air inlet, the generated vortexes are fewer, weaker and nearer to the air inlets when the inlet angle is 45 ° along the axial cross section.

与30°进气道相比，沿轴向横截面上45°进气道所形成的回流区向进气道一侧偏移，回流区区域减少，强度减弱。

The quality of a negative tapered hole was mainly determined by its inlet diameter and outlet diameter. Using wire with the same diameter to process the holes of a same inverted angle, a smaller entrance diameter was preferred.

倒锥形孔的加工质量主要与入口孔径、出口孔径相关，采用相同直径的电极丝，加工相同倒锥角度的微孔，如果入口孔径越小，加工质量越高。

Wind tunnel experiment of sidewall compression inlet with adjustable attack angle

攻角动态变化的侧压式进气道风洞实验

Owing to the large inlet and outlet angle of blade and short flow passage, the flow field in an impeller of forward-curved multi-blade centrifugal fans was very complex.

前向多叶离心风机广泛应用于空调系统。由于该风机叶片进出口角大、流道短，叶轮内部气体流动非常复杂。

The existence of angle of attack reduces the inlet performance.

攻角的存在也在一定程度上降低了进气道性能.

Through lowering the air inlet total pressure, reducing the compression angle of air, increasing the nozzle length, cutting down the nozzle radius and the axial gap of electrode, the arc ignition energy can be improved.

通过减小流动压差、缩小空气压缩角、增加喷孔长度、减小喷孔半径以及减小轴向间隙等可以有效提高电弧的点火能量。

Through numeric value simulation of transition flue duct between outlet of the gas turbine and inlet of the boiler proper, the velocity distribution in outlet flue duct with upper surface plate of different elevation angle has been obtained.

通过对燃气轮机出口与锅炉本体进口之间过渡烟道的数值模拟，得出不同仰角上面板烟道出口的速度分布。

Inlet ramp regulating system using compensatory change of angle of attack

采用补偿攻角变化的进气道斜板调节系统

the influences of variations in speed and inlet port elevation angle on the scavenging process are investigated via simulating scavenging and exhaust processes of motored two stroke diesel engine by using multi dimensional digital simulating method.

利用多维数值模拟方法，对二冲程柴油机倒拖情况下的进、排气过程进行模拟，研究转速变化、进气口仰角变化对扫气过程的影响。

The model can also be used for optimizing the design parameters, such as inlet flow rate, susceptor tilt angle, etc.

所得的结果有助于增进对这类反应器中的传输过程的认识，模型亦可用于设计参数的最优化，诸如入口流量，锥台倾角等。

The calculating result showed that impeller outlet diameter D2 effects on the head largest of these parameters, vane outlet angle β 2 smallest, inlet diameter D1, outlet width b2, vane number Z and vane length ratio R were between them successively.

计算结果表明，在这些几何参数中，叶轮出口直径D2对扬程影响最大，叶片出口角2β影响最小，进口直径D1，叶轮出口宽度b2，叶片数Z和叶片长度比R依次地处于它们之间。