interfacial stress的例句大全

When a micro interfacial stress is applied to the novel surface acoustic wave interfacial stress sensor, the input-output of the sensor is a simple linear function. We built the linear regression model and solved it by the least squares method. 4.

当新型声表面波压力传感器加载微压力时，其输入输出函数是一元线性函数，所以只需建立其一元线性回归模型，并利用最小二乘法求解即可。

Interfacial stress and normal stress of adhesive increase with the increase of shorting length of CFS-GFS.

随着纤维布有效粘贴长度的减小,胶层端部界面剪应力与正应力成比例增加,增加比例随距离的增加,呈递减趋势.

Analysis of interfacial stress on coatings based upon hertz contact theory

基于Hertz接触理论的涂层界面应力分析

Surface and interfacial stresses are slightly affected by FeAl layer. Therefore, when choosing thick ceramic layer and thin Al layer, there are appropriate stress distributions at surface and interfaces, and the mechanical properties of coatings can be strengthened.

FeAl层对表面应力和界面应力影响较小.因此，当选择较厚陶瓷层和较薄铝层时，涂层内将具有较优的表面和界面应力分布状态，从而可提高涂层力学性能。

Interfacial stress distribution on immediately loaded micro-implant with different tapers: Finite element analysis

微植体锥度对即刻加载时界面应力分布影响的三维有限元分析

Based on the crystallography properties of carbon fiber, a method of determining the interfacial residual stress in carbon fiber reinforced epoxy composites by X ray diffraction technique was established in this paper.

根据碳纤维的晶体学特点，提出了利用X射线衍射技术分析碳纤维/树脂基复合材料界面残余应力的新方法。

Analysis of Stress Intensity Factor of Interfacial Crack in TBC The Method of the Local Moment Estimation

局部配置法求解TBC界面裂纹应力强度因子研究

The interfacial shear stress is a constant proportion of the bottom shear.

交界面的剪力与底部剪力之比是常数.

In the case of polymer-wood composites, the interfacial adhesion influences the stress transfer from the xylon to the polymer matrix, the mechanical properties, water absorption and dimensional stability of the composites.

对于木塑复合材料而言，木质填料与树脂基体的界面粘接程度是有效传递载荷、提高力学性能、降低吸水率和提高尺寸稳定性的关键因素。

The interfacial failure due to thermal stress will increase with increasing the range of temperature and the number of cycles.

随着冷热循环温度区间温差的增大、冷端温度的降低、循环次数的增多，形成的热应力对材料的界面损伤越严重；

The interfacial shear stress and peel stress between the FRP and the surface of tension flange were analyzed when the FRP was bonded to the tension flange of the bending members.

对受弯构件受拉翼缘外侧粘贴FRP后的界面剪应力和界面剥离应力进行了分析。

The effect of the interfacial residual stress on the stress concentration became less with the increase of tensile elongation.

在低拉伸时，界面残余应力对应力集中的影响较大，但在高拉伸，特别是达到材料伸长率时，界面残余应力的作用可忽略。

It is shown that the joint strength increases firstly and then decreases gradually with the increase of joining temperature, and the maximum value of strength is obtained at 850 ℃ because of the effect of ceramic-metal interfacial reaction and residual stress.

结果表明，由于陶瓷／钎料界面反应和界面残余应力的综合影响，随着钎焊温度的增加，接头强度先增加然后逐渐降低，850℃钎焊时接头强度最高。

under the same conditions, the interfacial failure of composites differs for different relaxation of the thermal stress of interfaces.

不同的复合体系由于其界面松弛热应力的能力不同，在同样条件下的冷热循环过程中，界面所受到的损伤程度有差异。

When YAS solder is mixed with Si 3N 4 powder, the interfacial thermal stress may be decreased, and the joint strength is enhanced.

而在YAS钎料中添加Si3N4，可以降低接头界面的热应力，改善接头强度。