interference fit的例句大全

Choice Selecting Interference Fit with computer

应用微机选择过盈配合

Analysis and Improvement of Interference Fit Reliability of Thin-walled Bearing Shell

薄壁轴瓦过盈配合可靠性分析及改进

Wheelset is a key moving component on the bogie frame in locomotive and vehicle, which combines two wheels with an axle together firmly at the mode of keyless and interference fit.

轮对是列车走行部件的基础，是转向架部件的关键件，其生产方式是用轮对组装设备将车轮与车轴进行过盈无键组装配合，使之牢固结合在一起。

Before the assembly of parts of the match, especially interference fit the size and the relevant review.

装配前应对吾爱内用抗菌乳膏零、器件的首要配合尺寸，特别是过盈配合尺寸及相关精度进行复查。

Fatigue life increment of interference fit tapered shank bolt connections under random loading

随机载荷作用下锥形螺栓干涉配合的疲劳寿命增益

experimental study on optimum interference-fit level of interference fit

干涉配合最佳干涉量初探

bearings with a tapered bore are always mounted with an interference fit .

带圆锥孔轴承始终以过盈配合安装。

for bearings having a tapered bore , inner rings are always mounted with an interference fit .

对于圆锥孔轴承，内圈的安装始终采用过盈配合。

application of interference fit in transformation of universal joint spindle

过盈联接在万向接轴改造中的应用

in this paper, we give an analysis for friction& free interference fit bolt using the finite element method.

本文采用有限元素方法在螺纹面无摩擦力的条件下对过盈配合的螺栓、螺母进行了分析计算。

this paper deals with designed theory and method for interference fit between plastic shaft and plastic hub.

陈述了塑料实芯轴与孔座间过盈连接的设计理论和方法。

This paper describes the application of projected tolerance zone, mainly in threaded parts and parts with interference fit to control the tole ranee in position or symmetry so that the function and assembling of these parts be ensured.

本文论述了延伸公差带的应用，主要用于螺纹件及压配合零件的连接，控制位置度和对称度的公差，以保证零件的功能要求和顺利装配。

Shrinkage fit is a way to realize the tight joint through the interference between enveloping parts ( hole) and enveloped parts ( shaft).

过盈联接是以包容件（孔）和被包容件（轴）配合后的过盈值来达到紧固联接为目的。

The items of Zernike polynomials have corresponding meanings of Seidel aberrations. The method of using Zernike polynomials to fit optical surfaces has been widely used in project, optical design software and interference check.

由于Zernike多项式的各项与光学像差有相应的对应关系，用Zernike多项式对镜面面形数据进行处理的方法已经广泛应用于工程项目、光学系统设计软件和干涉检查等。

To have an interference or force fit between mating parts, the tolerances must be such as to create a zero or negative allowance.

为了使配合零件之间具有过盈或强制配合，公差必须产生零或负允差。

the experimental results obtained show that suitable interference can certainly increase fatigue life in comparison with the push-fit case.

结果表明，适量干涉能有效地提高连接区的疲劳寿命。

According to practical production the principle of typical press fit joint and the calculation methods for design stress, pull out strength, diametrical interference and thermal expansion coefficent are introduced.

从生产实际出发，介绍了典型压配联接的原理以及设计应力、压出力、径向过盈量和热膨胀的计算方法。

application and methods to fit optical interference wave surface with quantizing technique

光学干涉波面数字化处理方法与应用

computer room light should be fit, not too bright or too dark, to avoid direct exposure to light in the screen caused interference of light.

电脑室内光线要适宜，不可过亮或过暗，避免光线直接照射在荧光屏上而产生干扰光线。

The primary factors for influencing working space are analysed. The restriction conditions are deduced, such as parallel bar length, motion fit corner, parallel bar interference and framework restriction.

分析了影响工作空间的主要因素，推导出并联杆长度、运动副转角、并联杆干涉和结构限制等的约束条件。