internal pressure的例句大全

Internal Pressure Measurement for Thick Wall Cylinder In Impact Fatigue Test

带内裂纹厚壁圆筒管冲击疲劳实验中内压测定技术

Development of Test System of Thermoplastic Pipe under Internal Pressure

管材耐内压试验系统的研制

Thermal Pressure Coefficient and Internal Pressure for Binary Solutions

溶液的热压力系数及内压

Prediction of thermal pressure coefficients and internal pressures for normal alkanes

正构烷的热压力系数及内压的预测

The Elasto-Plastic Finite Element Analysis of Thick-Walled Cylinder Under Internal Pressure and Its Application to the Final Sizing Technology of Welded Pipe End

受内压厚壁圆筒的弹塑性有限元分析及其在焊管管端定径工艺中的应用

An Engineering Analysis Approach for Squeeze Equal-diameter Tee Branch Pipe Connection Strength under Internal Pressure

等径挤压三通强度分析工程方法

A simplified hard-body equation of state and its applications(ⅱ) prediction of thermal pressure coefficient and internal pressure of liquids

简化刚体状态方程及其应用Ⅱ.液体热压力系数和内压的预测

The thermal pressure is obtained by the principle of corresponding state and the internal pressure is derived from Lennard-Jones ( 6,12) potential.

聚合物的热压力由对应状态原理得到，内压力由Lennard Jones（6,12）势能函数导得。

The relative formulations between limit loads ( both axial force and internal pressure) acting on it are derived while the whole thick-walled tube is led to the yielded state.

当整个厚壁圆筒达到屈服状态时，推导了在内压力和轴向力联合作用下的厚壁圆筒的塑性极限载荷表达式。

Ring Tension Stress Analysis of Elliptic Section Bend Pipe by the Action of Internal Pressure

椭圆形截面管受内压作用的环向应力分析

In the present paper, the shakedown problems of power hardening and elastic power hardening thick-walled cylindrical tube under a cycling internal pressure are studied.

本文讨论了幂强化材料以及弹性&幂强化材料厚壁圆筒在循环内压作用下的安定性；

Study on Plastic Limit Load of Extruded Piping Tee under Internal Pressure

内压下挤压三通的塑性极限载荷研究

Simulation and analysis of the constant internal pressure spiral case with non-uniform gap

基于非均匀间隙的充水保压蜗壳施工仿真分析

Structural model test for surrounding concrete of steel spiral case keeping constant internal pressure

三峡水电站充水保压蜗壳三维仿真整体结构模型试验

Stress analysis of PSP under bending moment and internal pressure was also discussed.

分析弯矩对管材的影响，讨论了内压与弯矩联合作用下PSP管的应力应变。

This paper deals with the function relations of principal stress and principal stain of a thin-walled cylinder varying with time, and the relations between the principal stain rate and the thickness of a thin-walled cylinder, as it is subjected to internal pressure.

给出了薄壁圆筒受内压时，主应力、主应变随时间变化的函数关系，以及主应变速率与圆筒壁厚的联系。

The distribution of the stress in casing connection, the value of make-up torque and thread off load are studied when the casing connection is assembled or loaded with internal pressure and axial tension, which are very important for gluing, leakage and thread off failure analysis.

套管接头在装配、内压和拉伸载荷工况条件作用下，沿接头的应力分布规律、上扣扭矩和滑脱力的大小，对分析套管接头粘扣、泄漏和滑脱的失效有重要参考价值。

The tinier the bubbles, the greater their internal pressure. So when these babies blow, they can disperse their contents far and wide.

泡泡越小，内部压强越大。因此，当这些极小的泡泡们破裂时，便会携带着构成物四处飞散。

Effect of the examing pressure and temperature and moisture on the burst strengths of GRP internal pressure vesseles the ball pressure test

检验压力及温湿度对玻璃纤维缠绕内压容器爆破强度的影响

Besides, thickness distribution and useful height mainly depend on axial feed but not internal pressure.

除此以外，零件的厚度分布和有效成形高度对溢流压力不敏感，其成形质量主要取决于管端的轴向进给程度。