isothermal process的例句大全

Polytropic Process, Adiabatic Process and Isothermal Process of Varying Mass System

变质量系统的多方过程、绝热过程及等温过程

In light of the general method of solving mean value and in view of the isothermal process of both ideal and real gas, this paper presents a further exploration into the volume formula for surge chambers on slush pumps and thereby some new results.

本文用求平均值的普遍方法，针对理想气体和真实气体的等温过程这两种情况，考查了钻井泵空气包的体积公式，得到了一些新结论。

Replacing the equation of the quasi-static isothermal process by the quasi-static polytropic process of the ideal gas, the barometric formula of polytropic process is deduced, which is better improvement on the barometric formula of isothermal process.

用理想气体的多方过程方程取代等温过程方程，推导出气体处于多方平衡过程时的气压公式，该公式是对气体等温气压公式的一种很好的修正。

The improvement on the barometric formula in isothermal process of the gas

对气体等温气压公式的修正

This paper discusses the finite time availability of ideal gas system in constant volume process, constant pressure process 、 isothermal process and adiabatic process.

研究在给定约束的等容、等压、等温及绝热过程中，理想气体系统的有限时间可用性。

For compressor, the optimal compressing process is the isothermal process.

对于压缩机来说, 等温压缩是最理想的压缩过程.

Magnesium-aluminium-zinc alloys, unwrought Isothermal forging process of upper anti-torque arm of 2214 alloy

镁铝锌合金，未锻造2214铝合金上防扭臂等温模锻工艺的研究

Magnesium-aluminium alloy ( magnesium predominating), unwrought Isothermal Forging Process of 2214 Alloy Anti-torque Arm

镁铝合金（镁是其中主要成分）未锻造的2214铝合金防扭臂等温模锻工艺的研究

On the role of isothermal lines in thermodynamical process

浅谈等温线在热力学过程中的应用

Numerical Simulation of Three-dimensional Isothermal RTM Process Based on Solid Flow

基于实体流的三维等温RTM数值模拟

Study on the Process and Apparent Dynamics for the Preparation of Diaminopropane by the Ammonolysis of Dichloropropane; Curing Kinetics of Bisphenol-A Epoxy Resin with Polyamide by Isothermal Differential Scanning Calorimetry

二氯丙烷氨化合成丙二胺工艺及动力学研究等温DSC法研究聚酰胺与环氧树脂的固化动力学

ultra high strength aluminum alloy isothermal stamping process

超高强铝合金等温模锻工艺

Study of Numerical Simulation for Three-Dimensional and Isothermal Viscoelasticity on Full Slip Extrusion Process of Gas-assisted Dies

气辅口模完全滑移挤出成型过程的三维等温黏弹性数值模拟研究

The following main achievements were yielded: ( 1) Based on process characteristics of gas-assisted full slip extrusion molding and the theories of rheology and hydrokinetics etc., under reasonable assumption, full three dimension steady isothermal viscoelastic theoretical model of describing gas-assisted extrusion molding process is established.

针对气辅完全滑移挤出成型过程的特点，基于流变学和流体动力学理论，经合理假设，建立了描述气辅完全滑移挤出成型过程的全三维稳态等温粘弹性理论数学模型。

Isothermal Heat treatment Process Experiment of Batch-Produced ADI Gears

奥贝球铁齿轮批产等淬热处理工艺试验

isothermal heat treatment process;

等温处理工艺；

isothermal spheroidizing process for h13 hot-working die steel was studied in th is paper.

对H13热作模具钢的等温球化退火工艺进行了试验研究。

under consideration of cost, it is therefore suggested to let the isothermal tempering process last just for 30 min in practical use.

因此在成本考量之下，实际应用只需要进行30分钟的恒温回火持时就已足够。

research of foam density change in the process of freely extruding foam in isothermal condition

等温挤出发泡塑料泡体密度变化的研究

The isothermal quenching process of the ductile iron camshaft was analyzed.

对球铁凸轮轴的等温淬火工艺进行了分析.