joint bolt的例句大全

Addition of chamfering shape on seating surface of joint bolt atf cooler pipe area.

倒棱增加物的塑造在自动制冷管的范围内、头螺栓的座套表面.

Addition of chamfering shape on seating surface of joint bolt at atf cooler pipe area.

倒棱增加物的塑造在自动制冷管的范围内、接头螺栓的座套表面.

It's a important join component of hydrogenerator main shaft fasten joint bolt.

水轮发电机主轴联轴螺栓是水轮发电机重要的联接部件.

Breaks Treatment of Joint Bolt between Quill Shaft Flange and Mill Shell

水泥磨中空轴法兰与筒体联接螺栓断裂的原因与处理

As the bolt tension increase, the tension of rail web, stress of joint bar and stress of joint bolt would increase accordingly, but the displacement of rail would become smaller.

螺栓扭矩增大，接头区钢轨轨腰拉力、夹板应力、螺杆内应力都会增大，而钢轨位移会随着螺栓扭矩的增大而减小。

Oil of Sandalwood Reliability Design of Joint Bolt on Electric Submersible Pump Unit

潜油电泵机组联接螺栓的可靠性设计

Analyzing the brittle failure and improving the design of hign strength joint bolt on ladle turntable

钢包回转台高强度连接螺栓的脆断分析与设计改进

To guarantee the reliability and security of the steel construction, the clamp load of the joint bolt should be under strict control, sometimes even the tension of the bolt should be measured on-line.

为确保钢结构工程的可靠性和安全性，必须严格控制连接螺栓的紧固力，必要时还要在线监测螺栓工作应力。

Bolt hybrid joint have been described in this paper. The condition of control loadbearing capacity of hybrid joining by the strength matching of the weld and H.S. bolt in hybrid joining have been analyzed and experimented.

本文论述了焊接&高强螺栓混合连接的性能特点，试验并分析了在混合连接中用焊接和高强螺栓连接强度匹配控制混合连接承载力的条件。

research of the torsional moment factor about ordinary high strength bolt-joint

普通高强度螺栓副转矩系数的研究

mechanical behavior research for high strength bolt connection joint of main and secondary beam

主次梁承压型高强度螺栓连接节点受力性能研究

The valve adopt the bolt joint, it's construct simpleness , seal trustiness, capability choiceness, and examine-repair convenience.

阀门主体结构采用螺栓连接形式, 结构简单、紧凑 、 密封可靠、性能优良, 而且检修方便.

The improvement in diagram of deformation of bolt joint under axial load

紧联接螺栓受力变形线图的改进

FEM Analysis of Bearing Pressure at Bolted Joint for the Heterogeneous Bolt with the Internal Radius

异形内R型螺栓头部支承面压力有限元分析

The curve of relation of joint moment and rotation angle, end-plate thickness and forced load-bearing characteristic of bolt are analyzed;

对节点弯矩&转角曲线关系、端板厚度和螺栓受力特点进行了分析；

The article introduces the joint work of systematic bolt and prestressed bolt in a slope stablizing project.

文章介绍了系统锚杆与预应力锚杆结合在某边坡工程治理的应用。

According to the theory that the bolt and the joint plane have the same distortion, the optimal anchoring angle and distortion angle are discussed, which are following with the changes of the tangential joint displacement and joint friction angle.

本文从理论分析出发，以锚杆和节理面共同变形为基础，探讨了锚杆最优锚固角和变形角随节理切向位移和节理摩擦角变化的规律。

the calculation of bolt joint under the impact stress

冲击载荷作用下螺栓连接的计算

the pretightening force of frp construction bolt joint has been researched in the theory of bolt washer stress.

应用螺栓-垫圈应力理论对FRP结构搭接点预紧力进行了研究。

research on pin load distribution of multiple bolt-jointed composite laminate

复合材料多排螺栓连接钉载分配的研究